我在android 9.0.0_2.0.0以及Yocto L4.14.98_2.2.0环境下编译fw_printenv 和 fw_setenv时一直报错,请问有解决方案吗?log如下: ~/i.MX-L4.9.88-2.0.0-Yocto/imx-yocto-bsp/build-xwayland-imx8mqevk/tmp/work/imx8mqevk-poky-linux/u-boot-imx/2018.03-r0/git$ make envt...
$ MACHINE=imx93evk DISTRO=fsl-imx-xwayland source ./imx-setup-release.sh - b bld-imx93evk b. Use bitbake command to start the build process. Also, add the -c populate_sdk to get the toolchain. $ bitbake imx-image-full -c populate_sdk c. Install the Yoct...
首先在Uboot的env变量中添加了boot_limit,mmcbootpart,mmcbootpart_back三个变量,并且对它们添加了一定的逻辑判断,可以通过uboot命令行看到: u-boot=>printenvboot_limitboot_limit=3u-boot=> printenv mmcbootpartmmcbootpart=2u-boot=> printenv mmcbootpart_backmmcbootpart_back=3bsp_bootcmd=echoRunningBSPbootc...
首先在Uboot的env变量中添加了boot_limit,mmcbootpart,mmcbootpart_back三个变量,并且对它们添加了一定的逻辑判断,可以通过uboot命令行看到: u-boot=> printenv boot_limitboot_limit=3u-boot=> printenv mmcbootpartmmcbootpart=2u-boot=> printenv mmcbootpart_backmmcbootpart_back=3bsp_bootcmd=echoRunning BSP...
yocto kernel. Maintenance --- This layer is maintained by Wind River Systems, Inc. Contact <support@windriver.com> or your support representative for more information on submitting changes. Building the nxp-s32g layer --- This layer should be added to bblayers.conf. This is done automatically...
0件の賞賛 返信 07-23-202405:24 AM 1,260件の閲覧回数 rockerr Contributor II It seems that fw_printenv still has access to the uboot env even though the original u-boot config is not altered. 0件の賞賛 返信
2. cd ~/imx-yocto-bsp-5.4.3_1.0.0 3. run below comands # DISTRO=fsl-imx-fb MACHINE=imx6sxsabresd source imx-setup-release.sh -b build_sabresd# bitbake u-boot-imx-fw-utils -c compile # bitbake u-boot-imx-fw-utils -c install then you will get fw_printenv & fw_setenv ...
What should I do to use fw_printenv/setenv on imx8mm? 【Conditions】 ・hardware: imx8mm(on custom board) ・bsp: imx 6.1.55-2.2.0 ・base image: core-image-minimal・IMAGE_INSTALL += "u-boot-fw-utils"・MACHINE = 'imx8mm-lpddr4-evk' ・boot storage:emmc 【log】 ...
fw_setenv/fw_printenv: https://github.com/sbabic/libubootenv.git Note: Please do not use uboot fw_setenv/fw_printenv Compile it on the host x86/x64 PC. It is used on host. b. u-boot-initial-env Under uboot, make u-boot-initial-env Note: Yocto deploys u-boot-initial-...
yocto kernel. Maintenance --- This layer is maintained by Wind River Systems, Inc. Contact <support@windriver.com> or your support representative for more information on submitting changes. Building the nxp-s32g layer --- This layer should be added to bblayers.conf. This is done automatically...