nrf_gpio_pin_dir_t dir, nrf_gpio_pin_input_t input, nrf_gpio_pin_pull_t pull, nrf_gpio_pin_drive_t drive, nrf_gpio_pin_sense_t sense) //GPIO端口状态配置 { //配置端口 NRF_GPIO_Type * reg = nrf_gpio_pin_port_decode(&pin_number); //配置对应的端口的状态 reg->PIN_CNF[pin_nu...
第一个GPIO为GPIO0.1,低电平有效;第二个GPIO为GPIO1.2,低电平有效。 n: node { foo-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>, <&gpio1 2 GPIO_ACTIVE_LOW>; } 接下来我们可以使用gpio_dt_spec来获取device tree中定义的GPIO。 gpio_dt_spec结构体包括以下三部分,分别对应device tree中GPIO的三个参数。 ...
TASJK 任务通过通道 OUT[0]-OUT[7] 设置输出触发状态,Event 则可以通过检测信号产生 PORT event 事件,产生 IN[n] event 事件。 整个GPIOTE 寄存器的个数非常少。GPIOTE 模块提供了 8 个通道,这 8 个通道都是通过 CONFIG[0]~CONFIG[7] 寄存器来配置。八个通道可以通过单独设置来分别和普通的 GPIO 绑定。当...
nrf_gpio_pin_read(uint32_t pin_number) //读取某个引脚的电平 nrf_gpio_word_byte_write(volatile uint32_t * word_address, uint8_t byte_no, uint8_t value) //写多个port的值 nrf_gpio_word_byte_read(const volatile uint32_t* word_address, uint8_t byte_no) //读多个port的值 nrf_gpio...
接下来我们可以使用gpio_dt_spec来获取device tree中定义的GPIO。 gpio_dt_spec结构体包括以下三部分,分别对应device tree中GPIO的三个参数。 port:GPIO 端口设备指针 pin:GPIO的PIN NUM dt_flags:gpio在device tree中定义的配置 flags。这些flags在中定义。包括GPIO_ACTIVE_HIGH, GPIO_ACTIVE_LOW, GPIO_PULL_UP...
(nrf_gpio_pin_read(CHARGER_CHARGING_PIN) &0xFF);#endifif(charger) {#ifdefCHARGER_CHARGING_PINif(charging)returnInCharging;returnChargingComplete;#elsereturnInCharging;#endif}else{returnNoCharge; } } 开发者ID:1072258106,项目名称:duband,代码行数:37,代码来源:bd_charging.c...
实验步骤 162 第十一章:GPIO 任务和 (GPIOTE) 164 1. 学习目的 164 2. GPIOTE 原理 164 2.1. GPIOTE 功能 164 2.2. 引脚任务和 165 2.3. PORT 165 3. GPIOTE 寄存器 166 4. 软件设计 171 4.1. 库函数的应用 171 4.2. GPIOTE 输出流程 172 4.3. GPIOTE 输入流程 177 4.4. GPIOTE 通道输出实验 179 ...
nrf_gpio_cfg_input(13,NRF_GPIO_PIN_PULLUP);//key 1nrf_gpio_cfg_input(14,NRF_GPIO_PIN_PULLUP);//key 2NVIC_EnableIRQ(GPIOTE_IRQn);//Enable External Interrupt//key1NRF_GPIOTE->CONFIG[0] = (13<< GPIOTE_CONFIG_PSEL_Pos)//IO port| (GPIOTE_CONFIG_MODE_Event << GPIOTE_CONFIG_MODE_...
When an OUT[n] task or an IN[n] event has been configured to operate on a pin, the pin can only be writtenfrom the GPIOTE module. Attempting to write a pin as a normal GPIO pin will have no effect.当IO配置为GPIOTE后,GPIO操作将无效,直到GPIOTE释放此脚 PORTevent 示例分析(): typedef...
GPIOUARTUART P0.08RTSCTS P0.09TXDRXD P0.10CTSRTS P0.11RXDTXD Table4nRF51822DevelopmentDongleUARTconfiguration Note:TheUARTsignalsarerouteddirectlytotheSEGGERchip.Thepinsshouldonlybeusedfor UART.InordertousetheUSBtoUARTbridge,thesoftwareonthenRF51822hastoenable flowcontrol.FordetailsonhowtosetuptheUARTwith...