52840由于GPIO多出了P1,需要对多出来的P口进行拓展,可定义为以下方法使用不同的PORT口 #define LED_1 NRF_GPIO_PIN_MAP(0,13) //定义P0.13 #define LED_2 NRF_GPIO_PIN_MAP(1,13) //定义P1.13 nrf_gpio_cfg_output(LED_1); //初始化P0.13为输出 nrf_gpio_cfg_output(LED_2); //初始化P1.13为...
foo-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>, <&gpio1 2 GPIO_ACTIVE_LOW>; } 接下来我们可以使用gpio_dt_spec来获取device tree中定义的GPIO。 gpio_dt_spec结构体包括以下三部分,分别对应device tree中GPIO的三个参数。 port:GPIO 端口设备指针 pin:GPIO的PIN NUM dt_flags:gpio在device tree中定义的配置...
- 如果函数在头文件中声明,确保在源文件中定义时使用了相同的参数和返回类型。 ### 7. **错误:`error: 'NRF_GPIO_PIN_MAP' undeclared`** - **原因**:可能没有包含正确的头文件,或者使用的SDK版本不兼容。 - **解决办法**: - 确保包含了`nrf_gpio.h`头文件。 - 检查使用的SDK版本,确保与NRF52840...
nrf_gpio_cfg_output() //set GPIO as output nrf_gpio_pin_set() //Drive the specified GPIO output high nrf_gpio_pin_clear() //Drive the specified GPIO output low nrf_gpio_pin_toggle() //Reverses the output state of the specified GPIO NRF_GPIO_PIN_MAP() //Map port and pin numbers ...
开发板:初雪得100出头那块NRF52840 EVAL KIT 下载器:JLINK V8固件,已经更新到最新的固件了,我用过ST LINK,和DAP都可以下载,但一旦全片擦除要解锁芯片写保护...) | ((pin) & 0x1F)) 用来映射GPIO引脚的,比如P1.9就是0x29 LED初始化代码#define LED0NRF_GPIO_PIN_MAP(0,13) #define ...
Widest Range of Configurable Interfaces - UART, I2C, SPI, ADC, GPIO, PWM, FREQ, USB, and NFC 2Mbps & LE Long Range - Support for 2 Mbps, 1 Mbps, and 125 kps coded Hostless Operation with Powerful Core - Internal MCU reduces BOM and Cortex-M4F (1 Mbit Flash, 256k...
nrf_gpio_pin_toggle()//翻转指定的GPIO的输出状态 NRF_GPIO_PIN_MAP()//将端口和引脚编号映射到数值 其中,NEF_GPIO_PIN_MAP()将端口和引脚编号映射到数值指的是将P0.0至 P0.31映射为0至31,将P1.0至于P1.15映射为32至47。 4.1.3流水灯实验 下面将进行代码编写,此处代码对应的提供的例程为:001_LED。 首...
6、各外设功能介绍1、GPIOregisters共有31个GPIO管脚(P0.0P0.30),可以通过管脚配置寄存器PIN_CNFn(n=0.30),对每个管脚进行单独的配置,配置的参数包括:DirectionDrivestrengthEnablingofpull-upandpull-downresistorsPinsensi 23、ngInputbufferdisconnectAnaloginput(forselectedpins)2、GPIOTE(GPIOtasksandevents)功能:利用...
led0: led_0 { gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; label = "Red LED"; }; ... } It corresponds with the 26 pin on the board. For the pins with the Xiao breakut you don't need to use the &gpio0 pin mapping directly as the board files provide a Xiao connector which simpli...
Addconf()utility function to reduce code duplication in GPIO (#250). Assets2 01 Aug 22:24 jonas-schievink v0.11.1 8dbcd37 Compare v0.11.1 New Features Add support for the Watchdog Timer peripheral (#175) Support VDD source for the ADC (#181) ...