@文心快码BaiduComatelinux no-carrier,broadcast,multicast,up 文心快码BaiduComate 在Linux系统中,ifconfig命令(或其现代替代品ip命令)用于显示和配置网络接口的状态和参数。当你查看网络接口的状态时,可能会看到如no-carrier、broadcast、multicast和up等标志。下面我将逐一解释这些标志的含义,并提供可能导致这些状态出现...
link set down:空 + state DOWN ifconfig命令 工作正常情况下:UP+RUNNING VM虚拟机模拟拔网线,网络设备状态 UP+无RUNNING ip link set dev eth1 down之后,网络设备状态 无UP+无RUNNING 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000 实际是...
2: eno1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen ...
Kubernetes网络通信中的no-carrier、broadcast和multicast 作为一名经验丰富的开发者,我将向你介绍在Kubernetes中如何实现no-carrier、broadcast和multicast这三个关键词。首先让我们来了解一下这三个概念在网络通信中的含义。 -no-carrier: 指网络接口没有物理连接,无法传输数据。 - broadcast: 广播是一种网 ...
The link has an IP address, but is not able to ping anything other than itself: Raw 3: enp7s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000 link/ether 0a:1b:2c:3d:4e:5f brd ff:ff:ff:ff:ff:ff ...
DEVICE TYPE STATE CONNECTION eno16780032 ethernet connected eno16780032 lo loopback unmanaged -- eno16780032: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether 00:50:56:94:3c:da brd ff:ff:ff:ff:ff:ff ...
As for the ip set link ib0 up command it is unnecessary. In the output of ip link/addr the following portion is given: ib0: <NO-CARRIER,BROADCAST,MULTICAST,UP> I have bolded the relevant portion that shows the interface is already logically up leaving this command with nothing to do. ...
3: enp1s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000link/ether b4:96:91:b5:96:4c brd ff:ff:ff:ff:ff:ff Can anyone suggest that what is missing or wrong? Thank you, dxyz_tiger Translate 0 Kudos Reply Al...
6: vbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000 link/ether ce:98:30:fe:38:4b brd ff:ff:ff:ff:ff:ff Any ideas? MrSorcus, bitraft, LaKing, poscat0x04, and DasSkelett reacted with thumbs up emoji ...
During boot the interface is up on the switch. Only when pfsense configures the interfaces at boot, the interface goes down on the switch. ifconfig ix1 shows: ix1: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500 ...