DP83848K: no phy at addr -1Rizwan syed Prodigy 30 points Part Number: DP83848K Hi All, I am using i.MX8DXL Custom board with Linux kernel 5.4.70.MY phy is DP83848 connected to EQOS controller on i.MX8DXL Custom board.Added the dts and pin changes required for Ethernet DP83848...
[ 13.286553] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1 Expand Quote root@arm-64:~# dmesg | grep -i wlan0 [ 7.013085] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=7c:a7:b0:5c:1b:3c [ 12.616850] RTL871X: rtl8188f_FirmwareDownload(wlan0) tmp_ps=3 ...
root@odroidc2:~# dmesg |grep -i eth0 [ 38.250881] meson8b-dwmac c9410000.ethernet eth0: no phy at addr -1 [ 38.251632] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19) [ 38.326577] meson8b-dwmac c9410000.ethernet eth0: no phy at addr -1 ...
No eth phy detect这句,其实只是MDIO去和Phy进行通信的一个标志,可以认为是mac和phy之间配置是通了。这个不通,一般的原因就是phy id(phy addr)不匹配。 EVM和APPRO的机器,PHY ADDR是不同的。EVM是0,而Appro是1. 建议你可以检查一下Phy芯片上phy id的管脚是否做了上下拉,对应的phy id到底...
The CPSW9G is configured as a virtual port in Linux, and the R5F Ethernet Firmware is responsible for the configuration and managment of the CPSW9G switch, MAC ports, PHY configuration. Linux details are athttp://software-dl.ti.com/jacinto7/esd/processor-sdk-linux-jacinto7/latest/exports/doc...
Describe the bug There is a performace issue between wlan and lan/wan OpenWrt version r25874-98f9154316 OpenWrt release SNAPSHOT OpenWrt target/subtarget qualcommax/ipq807x Device Zyxel NBG7815 Image kind Self-built image Steps to reprod...
for PFE_MDIO: addr 1 phy_connect failed Noethernetfound. 的OpenWrt [8.127382] pe_load_ddr_section:加载 人走了2022-01-05 07:10:33 dayu200烧写daily版本后启动串口报错no erthernetfound Device 0: unknown deviceNoethernetfound.missing environment variable: pxeuuidmissing environment ...
已发帖子： 669 积分： 802 个人网站 Re: adb提示No space left on device 首先，“/” 分区是只读...
Description Hi, root@DietPi:~# ls /dev/apex_0 ls: cannot access '/dev/apex_0': No such file or directory I found similar issues already discussed, like here, but disabling "Secure Boot" doesn't help in my case. dmesg: [ 0.000000] microco...
phy#0 Unnamed/non-netdev interface wdev 0x9 addr 70:cf:49:bb:a3:82 type P2P-device txpower 0.00 dBm Interface wlp3s0 ifindex 3 wdev 0x1 addr 70:cf:49:bb:a3:82 ssid dinwwpenwd type AP channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz txpower 22.00 dBm multicast ...