Hi, I tried to follow your instructions, but something wrong happened. it shows "Adafruit_I2CDevice.h: No such file or directory" It has been a long since I have been stuck in. Can you help to tackle it? I'm running the ESPHome version(2...
creating file ERROR: when checking for threshold files: Exception('failed to create battery start_threshold threshold: ', 'TypeError("\'<\' not supported between instances of \'str\' and \'int\'")') BAT0 start threshold = cat: /sys/class/power_supply/BAT0/charge_start_threshold: No su...
no valid processor ID found分享: 首次安装Qt后,创建项目时出现“No valid kits found” 的解决办法Wizard运行到 Kit Selection 就进行不下去了。 错误提示如下图: No valid kits found. 按照提示点击“options”,看到 手动设置/桌面(默认)前面有个叹号。说明 ...
0000:00:15.0 Serial bus controller: Intel Corporation Alder Lake PCH Serial IO I2C Controller #0 (rev 01) 0000:00:16.0 Communication controller: Intel Corporation Alder Lake PCH HECI Controller (rev 01) 0000:00:1f.0 ISA bridge: Intel Corporation Device 519d (rev 01) 0000:00:...
: clk id 142 not found”。任何关于为什么“找不到”I2C6 时钟的建议将不胜感激。I2C4/6 为 HSI 配置。完整的控制台输出:U-Boot SPL fdhsfagd 2023-01-10 06:01:32 jlink刷机V8固件的方法 连接jlink,大约10秒后,先断开USB连接,再断开TST连接;4,双击点开安装完成的《SAM-BA v2.14》,弹出如下对话框...
Re: adb提示No space left on device 首先，“/” 分区是只读的，可以重新mount为rw解决；但应该分区...
[ 3.305988] imx-dwmac 428a0000.ethernet: Using 32/32 bits DMA host/device width[ 3.324411] remoteproc remoteproc0: imx-rproc is available[ 3.341567] st_lsm6dsx_i2c 0-006a: supply vdd not found, using dummy regulator[ 3.348938] st_lsm6dsx_i2c 0-006a: supply vddio not found, using ...
[ 1.048379] hub 1-0:1.0: USB hub found [ 1.052225] hub 1-0:1.0: 1 port detected [ 1.057472] s32cc-rtc 40060000.rtc: registered as rtc0 [ 1.062707] s32cc-rtc 40060000.rtc: setting system clock to 1970-01-01T00:00:00 UTC (0) [ 1.070910] i2c_dev: i2c /dev entries driver [...
depends: i2c-core vermagic: 2.6.32-431.5.1.el6.x86_64 SMP mod_unload modversions parm: NVreg_Mobile:int parm: NVreg_ResmanDebugLevel:int parm: NVreg_RmLogonRC:int parm: NVreg_ModifyDeviceFiles:int parm: NVreg_DeviceFileUID:int
No! I use the OPi0+ on a PCB as MoBo as an EFIS w/ an Arduino Nano as analogue concentrator and GPIO extender w/ RS232, I2C, SPI, GPIO and a handful of sensors. Shutdown was just 1 function of it, I picked it as example, because its easy. The important issues for me to swi...