你看看你的不是输入的引脚是不是定义成输入了，比如接晶振的两个引脚定义成输入了，但是你这时又没输入。没输入就没驱动源，所以警告no driving source
Net has only one pin:单端网络管脚,当我们发现单端网络报错时,双击“Messages”里面的错误定位到有单端网络的地方,如图3-169所示。然后检查是否是因为网络标号名字填写 凡亿_PCB 2021-08-30 14:46:21 AD原理图编译has only one pin怎么办? 好像是电源VCC和J2的VCC不是同一个,不知道为什么不是同一个,(线旁...
Altium如何消除Net has no driving source警告 在Altium Designer中对原理图进行编译时,有时会有告警信息:Net has no driving source。下面就如何消除这个类型的告警信息进行说明。方法一:将对应元件的管脚类型修改 郑振宇altium 2019-09-17 14:42:11 NET1 NET1 - Currents Over 100 Amps - Power-One 2022-...
AbecedarioEntradas Atención al Cliente ‘nflow 11Sight 123 Flash Chat 123 Live Help 365Ticketing 3CLogic 4me ABC Live Chat Abhisi Help Desk AccessAble Help Desk Pro Acquire ActionTracker ActiveHelper Live Chat ActivEngage ActiveSeries Suite Adereso Helpdesk Aegis Help Desk Affinity Canvas Agentless...
2.0 V5.0 VFPGA auxiliary supply, VCCBAT; Backup battery; Real-time clock backup. 1.8 V12.0 VQDRII+ supply 1.8 V3.3 VFPGA GTX transceiver Quad PLL 1.5 V12.0 VDDR3; FPGA I/O Bank 34 1.2 V12.0 VFPGA GTX transceiver termination
Any 2-channel SPDT relay module with a high-level trigger should work. Typically there are 6 terminals on one side: NO/NC/COM for each relay, & 4 terminals on the other side: signal inputs for each relay (IN1/IN2), & power for the module (marked as +/-, or VCC/GND). There’...
2.0 V5.0 VFPGA auxiliary supply,VCCBAT; Backup battery; Real-time clock backup. 1.8 V12.0 VQDRII+ supply 1.8 V3.3 VFPGA GTX transceiver Quad PLL 1.5 V12.0 VDDR3; FPGA I/O Bank 34 1.2 V12.0 VFPGA GTX transceiver termination 1.0 V12.0 VFPGA GTX analog supply ...
1.5.10 Power VCCAC Power A/C Switching 1-36 Introduction 1.5.10 Power The VCCAC pins provide the 3.3V power for the switching component of the I/O output drivers. These pins can be filtered to lower any potential EMI. VCCDC Power DC Drive The VCCDC pins provide the 3.3V power for ...
load current Program memory Speed command / analog input (9 bit) UB I continuous I max f pwm I nom VCC Icc serial EEPROM voltage range frequency bandwidth speed range For combination with: Brushless DC-Servomotors PWM MVP2001A 12 to 40 8 30 24.58 150 5 250 8,190 0-5 500 250 1,000...
Part NO. VCC (V) VCC (V) VM (V) VM (V) Channel Exterior Serial Built-in Outputs Topology Package min. max. min. max. Control Control PI AT5561 N/A 5.5 N/A 10.5 1 N N 0 FS*1 DIP-8, SOP-8 AT5562 2.2 5 1.8 9 2 Y N 0 FS*2 DIP-16, SOP-14 AT5566 2.5 5.5 1.9 5.5...