实验一百二十三:Multi-function Shield多功能扩展板 Arduino实验12合1版 项目一:4个短哔声,重复3次 */#include<TimerOne.h>#include<Wire.h>#include<MultiFuncShield.h>voidsetup(){// put your setup code here, to run once:Timer1.initialize();MFS.initialize(&Timer1);// initialize multi-function ...
在Arduino中加载库: 然后就可以使用使用说明中的代码进行测试了, 比如让LED数码管显示内容: #include<TimerOne.h>#include<Wire.h>#include<MultiFuncShield.h>voidsetup(){// put your setup code here, to run once:Timer1.initialize(); MFS.initialize(&Timer1);// initialize multi-function shield librar...
实验一百二十三:Multi-function Shield多功能扩展板 Arduino实验12合1版 项目一:4个短哔声,重复3次 */ #include <TimerOne.h> #include <Wire.h> #include <MultiFuncShield.h> void setup() { // put your setup code here, to run once: Timer1.initialize(); MFS.initialize(&Timer1); // initial...
這一課我用 Arduino + Multi-Function Shield 來做kitchen timer,當然就是做 digital 的了。Digital kitchen timer 有什麼零部件呢? 從上圖可以見到 ,最基本的廚房計時器 ,會有一個 4 位數的顯示屏 ,用來顯示時間 ,另外會有 3 個 push button,用來設定 / 重設時間 ,和開始 /停 止 。當倒數完成 ,它會...
MultiWii的最初设置是在config.h文件中完成的.使用类似arduino ide或者文本编辑器来为多轴\固定翼\直升机来调整各种设置.通过增加或删除在#defing前的//来注释或取消注释掉这一行来使其生效. For instance, in the config file you choose the type of multicopter, minimum throttle for motors, i2c speed, ...
4. High extension: expand other sensors and modules through motor driver shield and sensor shield 5. Multiple controls: IR remote control, App control(iOS and Android system) 6.Basic programming:C language code of Arduino IDE. Specification Working voltage: 5v Input voltage: 6-9V Maximum output...
// If you're using hardware other than the unsped shield, you'll want to go through this portion of the code, // and change the pin numbers and atmega 168 PORTs that you're using. We're using pin/PORT assignments here, // NOT the pin number scheme from the arduino board outputs ...
7.7 Reset sources The reset signal of the STM32L4 Discovery kit is active low and the reset sources includes: • A reset button B1 • An ARDUINO® Uno V3 shield board from CN2 • An embedded ST-LINK/V2-1 7.8 USB OTG FS The STM32L4 Discovery kit supports USB OTG FS ...
Arduino: 1.6.8 (Windows 10), Board: WARNING: Spurious .github folder in ‘Adafruit Motor Shield library’ library In file included from sketch\Alarms.cpp:3:0: def.h:1960: error: #error “NUMBER_MOTOR is not set, most likely you have not defined any type of multicopter” #error “NUM...
在此定义Arduino串口号与UART速度 665 注:如在NMEA模式只有RX针脚是被使用的,GPS不可被multiwii配置 666 在NMEA模式下,GPS必须配置为输出GGA与RMC NMEA语句(在大部分GPS设备中通常为默认配置) 667 至少为5Hz更新速率。解除第一行注释来选择用于GPS的arduino串口 */ 668 669 //#define GPS_SERIAL 2 670 //...