执行命令mpls,进入MPLS视图。 执行命令mpls bfd-trigger [ host [ nexthop next-hop-address | outgoing-interface interface-type interface-number ] * | fec-list list-name ],配置动态BFD检测LDP LSP的触发策略。 缺省情况下,没有配置LDP BFD触发策略。 执行完该命令才真正开始创建BFD会话。翻译...
执行命令mpls bfd-trigger[host[nexthopnext-hop-address|outgoing-interfaceinterface-typeinterface-number]*|fec-listlist-name],配置动态BFD检测LDP LSP的触发策略。 缺省情况下,没有配置LDP BFD触发策略。 执行完该命令才真正开始创建BFD会话。 (可选)调整BFD检测参数 ...
[Sysname-ospf-1] segment-routing lsp-trigger host 1.1.48 segment-routing mapping-server advertise-local segment-routing mapping-server advertise-local命令用来开启通告本地SID标签映射消息功能。 undo segment-routing mapping-server advertise-local命令用来关闭通告本地SID标签映射消息功能。 【命令】 segment-rou...
segment-routing lsp-trigger { host | none | prefix-list prefix-name }缺省情况下,所有路由信息均触发建立SRLSP。1.14 配置优先使用SRLSP转发流量1.14.1 功能简介当到达同一目的网络同时存在SRLSP和LDP LSP两种标签转发路径时,设备优先使用LDP LSP转发流量。通过配置本功能,可以指定转发到达该目的网络的流量时优先...
[Huawei-mpls]lsp-trigger host //置触发静态路由和IGP路由建立LSP的策略, 缺省 [Huawei-mpls]lsp-trigger ip-prefix a1 //在Ingress和Egresspe配置触发静态路由和IGP路由建立LSP的策略 [Huawei-mpls]lsp-trigger none //在Ingress和Egresspe配置触发静态路由和IGP路由建立LSP的策略 ...
配置BFD for BGP Tunnel # 配置CSG,使能MPLS动态创建BGP BFD会话的能力,并将BGP BFD会话的触发策略设置为主机触发。 [CSG]bfd[CSG-bfd]quit[CSG]mpls[CSG-mpls]mpls bgp bfd enable[CSG-mpls]mpls bgp bfd-trigger-tunnel host[CSG-mpls]quit # 配置MASG,使能MPLS被动创建BFD会话功能。
配置BFD for BGP Tunnel # 配置CSG,使能MPLS动态创建BGP BFD会话的能力,并将BGP BFD会话的触发策略设置为主机触发。 [CSG]bfd[CSG-bfd]quit[CSG]mpls[CSG-mpls]mpls bgp bfd enable[CSG-mpls]mpls bgp bfd-trigger-tunnel host[CSG-mpls]quit # 配置MASG,使能MPLS被动创建BFD会话功能。
This command triggers Junos to generate and advertise adjacency SIDs. Do you remember them? They’re the segment IDs that are generated on each link that has an IGP adjacency. For each IS-IS adjacency, Junos will generate one segment ID for IPv4, and one for IPv6. It then advertises ...
Bidirectional forwarding detection (BFD) over VLAN is used as an FRR trigger to obtain more than 50 milliseconds of switchover time on the Cisco CRS-1. The following link bundle types are supported for MPLS-TE/FRR: •Over POS link bundles •Over Ethernet link bundles •Over VLAN...
This is true even if entering the protection local-prefixes command does not trigger an error message. Local link protection will only work properly if the failure is quickly detected and an alternate, backup route already exists. Therefore, in addition to the protection local-prefixes command, ...