What I still don't understand is: why do I have to set APN (access point name), USR, PSW, if I don't connect to the Internet using an Access Point? I want to connect to the Internet using GPRS directly, without passing through a Lan or through a Router which I have to connet t...
where RDS(on)_25deg is the on-resistance at 25 oC. In this example, RDS(on)_25deg = 0.27 Ohm. Step 5.Enter the Electrical Characteristics for the diode. The Vd vs IF curve can be captured as explained in the IGBT section. The test conditions must be entered, too. Step 6.Enter t...
12 HMUX 24 LMUX 9 HEN_TST GND 1 NC 2 NC 3 NC 7 NC 8 NC TPS7H6023/EM D1 SS1200-LTP BOOT BOOT BP5H BP5H BP5H HOH HOH HOH HOL HOL HOL PSW PSW PSW PSW ASW BST BST BP5L BP5L BP5L LOH LOH LOH LOL LOL LOL AGND PGND PGND PGND PGND 4 5 40 41 42 43 44 45 46 47 ...
ReservedCodeCacheSize=128m# Set the extra SBT options-DproxySet=true-Dsbt.log.format=true#-Dhttp.proxyHost=my-proxy-in.com#-Dhttp.proxyPort=8080#-Dhttps.proxyHost=my-proxy-in.com#-Dhttps.proxyPort=8080#-Dhttp.proxyUser=my_user#-Dhttp.proxyPassword="my_psw"-Dhttp.proxyHost=...
github.com/frankban/quicktest v1.7.2 // indirect github.com/go-errors/errors v1.1.1 // indirect github.com/go-redis/redis v6.15.7+incompatible github.com/go-redis/redis/v8 v8.4.4 github.com/go-sql-driver/mysql v1.5.0 github.com/gocql/gocql v0.0.0-20190829130954-e163eff7a8c6 githu...
PWMinverter).Thedevicelossesarethesumofconductionlosses,Pcond,andswitchinglosses,Psw.The samplingrateislow,forexample,intherangeof10/foutupto1s.Therefore,astaticthermalresistance, R,isused.Thelossesaretemperature-dependentwhichmeansaniterativecalculationwithTasan ...
the rsm is on IP 192.168.1.1 and the sup is on 192.168.1.1, I would set the sup to the .2 addr. Also you do not have vlan20 defined on the rsm. correct those and test again, also include sh vlan on sup and sh int on rsm if you still have problem. Be
PSW_N pin connected to VCC(3V3). JP6- Test mode jumper This jumper is only for factory test. The header should be left open for normal operation. Copyright © Future Technology Devices International Limited 11 UMFT313EV Datasheet Version 1.1 Document Reference No.: FT_000762 Clearance ...
Power loss calculations are: PIN=(VIN x IIN) + (V5V x I5V) (W) PSW=VSW x IOUT (W) POUT=VOUT x IOUT (W) PLOSS_MODULE=PIN - PSW (W) PLOSS_BOARD=PIN - POUT (W) EFFMODULE=100 x PSW/PIN (%) EFFBOARD=100 x POUT/PIN (%) (1) (2) (3) (4) (5) (6) (7) ...
The maximum drain-to-source current measured was ID = 52.4 A, each SiC device has a switching loss of PSW = 36 W (tested at 400 V), and the calculated conduction losses of Pcond.(max) = 20.86 W. Two scenarios can be distinguished for the thermal model. At Ta = 23 °C, Tjdie ...