在DeviceA上创建动态LACP模式Eth-Trunk接口,并将以太网物理接口加入Eth-Trunk接口。 <HUAWEI>system-view[HUAWEI]sysname DeviceA[DeviceA]interface eth-trunk 1[DeviceA-Eth-Trunk1]mode lacp-dynamic[DeviceA-Eth-Trunk1]quit[DeviceA]interface10ge1/0/1[DeviceA-10GE1/0/1]eth-trunk 1[DeviceA-10GE1/0...
动态LACP模式 服务器通过设备连接文件服务器,在设备上通过命令mode lacp-dynamic配置动态LACP模式Eth-Trunk接口连接服务器。当服务器重启后为空配置时,LACP协商超时,动态LACP协议可保证设备从文件服务器获取的数据成功转发给服务器。 当部署动态LACP模式Eth-Trunk接口的设备能够收到对端的LACP协议报文,两端设备将通过LACP...
动态LACP模式仅用于本地设备与服务器连接时。 动态LACP模式(Dynamic LACP Mode)是链路聚合技术中的一种配置模式,它基于IEEE 802.3ad标准,通过LACP(Link Aggregation Control Protocol)协议实现链路聚合的动态协商和管理。以下是关于动态LACP模式的详细解释: 应用场景: 动态LACP模式主要用于本地设备与服务器之间的连接。在...
表示支持802.3ad协议，和交换机的聚合LACP方式配合（需要xmit_hash_policy）.标准要求所有设备在聚合操作...
interface Eth-Trunk27port link-type trunkport trunk pvid vlan 181undo port trunk allow-pass vlan 1port trunk allow-pass vlan 60 100 to 104 122 124 128 142 181mode lacp-dynamic 关键配置 mode lacp-dynamic 服务器的网卡和网口，默认是多活逐流转发模式。华为交换机，默认是逐包转发。增...
parm: lacp_rate:LACPDU tx rate to request from802.3ad partner;0forslow,1forfast (charp) parm: ad_select:802.3ad aggregation selection logic;0forstable (default),1forbandwidth,2forcount (charp) parm: min_links:Minimum number of available links before turning on carrier (int) ...
Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Peer Notification Delay (ms): 0 802.3ad info LACP rate: fast ...
LACP configuration on Cisco switch. Link Aggregation Control Protocol IEEE 802.3ad (LACP) is an open standard of Ethernet link aggregation.
聚合绑定mode4 lacp、使用vlan id 打标签隔离的方法 组网及组网描述: 2022-03-08提问 举报 (0) 最佳答案 返璞归真 [H3C]interface bridge-aggregation 1 [H3C-Bridge-Aggregation1] link-aggregation mode dynamic [H3C-Bridge-Aggregation1] quit # 分别将端口GigabitEthernet1/0/1至GigabitEthernet1/0/3加入...
<HUAWEI>system-view[HUAWEI]sysname DeviceA[DeviceA]interface eth-trunk 1[DeviceA-Eth-Trunk1]mode lacp-dynamic[DeviceA-Eth-Trunk1]quit[DeviceA]interface10ge1/0/1[DeviceA-10GE1/0/1]eth-trunk 1[DeviceA-10GE1/0/1]quit[DeviceA]interface10ge1/0/2[DeviceA-10GE...