1. 解释错误代码-110通常代表的含义 在Linux系统中,尤其是在处理SD卡或MMC(MultiMediaCard)设备时,错误代码-110通常与设备访问问题相关。这个错误代码并不是标准的POSIX错误码,但在Linux内核和驱动程序中,它可能代表多种具体的错误,如设备未找到、初始化失败、通信错误等。具体到MMC0设备初始化SD卡时出现的-110错误,...
SDM439平台出现部分机型SD卡不能识别mmc1: error -110 whilst initialising SD card 打印了如下的log: 105-1018:01:02.699<3>[3079.000640] mmc1: data txfr (0x00100000) error: -110after163ms205-1018:01:02.699<6>[3079.000652] sdhci: === REGISTER DUMP (mmc1)===305-1018:01:02.699<6>[3079.000...
mmc0: erro..mmc0: error -110 whilst initialising SD cardmmc0: card never left busy state大佬给条腿抱一下,不介意腿毛
SDM439平台出现部分机型SD卡不能识别mmc1: error -110 whilst initialising SD card 打印了如下的log: 1 05-10 18:01:02.699 <3>[ 3079.000640] mmc1: data txfr (0x00100000) error: -110 after 163 ms 2 05-10 18:01:02.699 <6>[ 3079.000652] sdhci: === REGISTER DUMP (mmc1)=== 3 05-10...
[ 1.479870] mmc0: error -110 whilst initialising MMC card[ 1.546064] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using DMA[ 1.698156] mmc2: queuing unknown CIS tuple 0x01 (3 bytes)[ 1.725635] mmc2: queuing unknown CIS tuple 0x1a (5 bytes)[ 1.767939] mmc2: queuing ...
Re: TF卡启动报错 mmc init failed with error: -110 晕哥 说: 看上面的 log 降低 MMC 的频率, spl & u-boot 都跑起来了. 再把u-boot 里面的 DRAM 和 CPU 频率都降下来。 可以直接修改 .config 文件 DRAM 166MCPU 800M 就是配置这样两个是吧??CONFIG_DRAM_CLK=166CONFIG_SYS_CLK_FREQ=838860800...
mmc0: erro..mmc0: error -110 whilst initialising SD cardmmc0: card never left busy state大佬给条腿抱一下,不介意腿毛
不过一般情况下是物理线路的问题，即SD卡槽和SD卡之间的接触问题。插拔SD卡造成的静电也会出现这种情况。有一种饮正止渴的方法就是插入SD卡的时候压一下卡槽，减少SD卡槽与SD卡的间隙。避免因为静电或者接触不良造成的识别不了问题。出现这种问题就提醒您需要更换SD卡槽了，SD卡出问题的概率不大 ...
mmcblk0: error -110 sending status command, retrying mmcblk0: error -115 sending stop command, original cmd response 0x900, card status 0x900 mmcblk0: error -84 transferring data, sector 1097784, nr 256, cmd response 0x900, card status 0x0 mmc_host mmc0: Bus speed (slot 0) = 40000...
changed the titleSystem Bootup issue related to partitionodroid: sd card (mmc) error -110 transferring data against some cardson Aug 29, 2020 paralin mentioned this in 2 issueson Aug 29, 2020 Sign up for freeto join this conversation on GitHub.Already have an account?Sign in to comment...