Can't set block device Booting from net ... Error: ethernet@30bf0000 No valid MAC address found. Error: ethernet@30bf0000 No valid MAC address found. Error: ethernet@30bf0000 No valid MAC address found. Error: ethernet@30bf0000 No valid MAC address found. No ethernet foun...
Phy 4 not found cpsw, usb_ether Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc1 is current device SD/MMC found on device 1 switch to partitions #0, OK mmc1 is current device SD/MMC found on device 1 reading boot.scr ** ...
case BOOT_DEVICE_MMC1: spl_mmc_load_image(); break; 这样的修改可以实现上面提到的启动流程吗? 现在我在 Beaglebone Black 上试了下,好像不行,有如下打印说 MMC device not found: USB Host mode controller at 47401800 using PIO, IRQ 0 11 boot device - 8 MMC Device 0 not found spl: mmc devic...
bootcmd=run findfdt; run init_console; run envboot; run mmcboot; setenv mmcdev 1;setenv finduuid part uuid mmc 1:2 uuid;run mmcboot;run nandboot;run distro_bootcmd/*默认的envboot */envboot=mmc dev mmcdev;ifmmcrescan;thenechoSD/MMCfoundondevicemmcdev;ifmmcrescan;thenechoSD/MMCfound...
问题4:"powermt display dev=all "Device(s) not found"" 平台:HP-UX, IBM AIX, Red Hat Linux, UNIX 软件:PowerPath 5.0 问题描述:使用命令powermt display dev=all无法查看新加SCSI磁盘设备 解决方法:在emcgrab日志"powermt display options"文件检查PowerPath阵列状态是否设置为“managed”,或在主机运行命令pow...
与其他的设备驱动一样,mmc的驱动也分为控制器驱动和设备器驱动,但是不同的是mmc的设备器驱动是统一的,在/drivers/mmc/card/里面已经实现了,不需要我们进行实现;mmc控制器驱动使用的也是platform总线来进行连接的,在arcm下面进行platform_device的添加,在/drivers/mmc/host/下面进行platform_driver的注册。
[ 1220.796987] Aborting journal on device mmcblk1p4-8.[ 1220.797033] mmc1: running CQE recovery[ 1220.797152] mmc1: running CQE recovery[ 1220.797269] mmc1: running CQE recovery[ 1220.797339] print_req_error: I/O error, dev mmcblk1, sector 41538504[ 1220.797347] Buffer I/O error on ...
staticintdw_mci_rockchip_probe(structplatform_device *pdev) {conststructdw_mci_drv_data *drv_data;conststructof_device_id *match;intret;booluse_rpm =true;if(!pdev->dev.of_node)return-ENODEV;if(!device_property_read_bool(&pdev->dev,"non-removable") && ...
根据教程移植的系统，烧录QSPI+EMMC 烧录成功后从QSPI启动找不到EMMC1 MMC Device 1 not found no mm...
It seems like a build in card reader on your machine does not have a specific driver installed.Check Device Manger and update driver software for your card reader and USB.RegardsPlease remember to mark the replies as answers if they help. If you have feedback for TechNet Subscriber Support,...