mmc命令(MMC command) Steps: 1. Memory processing 1.1: check whether the memory of 0USES md. B 00x50 1.2: if the user is clear, mw. B 00xff 0x50 2. Read the files in MMC 0 into memory 2.1: read 10240bytes (10k) into memory from MMC; Fatload MMC 0 0u-boot.bin 0x2800. Of...
If the--remove-attributeparameter is specified, the command removes the attributes that are specified by the--attributeparameter from their current associations. If the--remove-groupparameter is specified, the command removes the groups that are specified by the--groupparameter from their current asso...
If the--remove-attributeparameter is specified, the command removes the attributes that are specified by the--attributeparameter from their current associations. If the--remove-groupparameter is specified, the command removes the groups that are specified by the--groupparameter from their current asso...
mmc command. 目前Mboot支持以下mmc命令: 1) mmc read/write. 读写命令。Addr =内存地址,blk# =起始block数,size =需要读写的大小。 比如:#mmc read 0x50000000 0x400b 0x400000,表示从第0x400b块(0x400b*0x200 = 0x801600)处开始读0x400000 bytes大小数据到内存0x50000000。返回打印OK说明读成功。 #...
1.Command:由host发送到卡设备。使用CMD线发送。 2.Response:从card端发送到host端,作为对前一个CMD的对应,通过CMD线发送; 3.Data:即能从host传输到card,也能从card传输到host。通过data线传输。 一、Commands 下面是四种用于控制卡设备的指令类型,每一个command都是固定的48位长度: ...
MMC命令(Management Console Command)是运行在Linux系统上的一种管理控制台命令,它提供了一系列管理与监控Linux系统的功能。MMC命令可以用于检查系统状态、配置网络设置、管理存储设备等。下面将详细介绍MMC命令在Linux系统中的使用方法和操作流程。 1. 安装MMC命令 ...
1、R1(normal response command):用来响应经常使用指令; 2、R2(CID,CSD register):用来响应CMD2和CMD10或CMD9。并把CID或CSD寄存器作为响应数据。 3、R3(OCR register):用来响应ACMD41指令,并把OCR寄存器作为响应数据; 4、R6(published RCA response):分配相对卡地址的响应。
1. Command: 用于开始传输的命令,是由HOST端发往DEVICE端的,其中命令是通过CMD信号线传送的; 2. Response: 回应是DEVICE返回的HOST命令作为Command的回应。也是通过CMD线传送的; 3. Data: 数据是双向的传送的。可以设置为1线模式,也可以设置为4线模式。数据是通过DAT0-DAT3信号线传输的。
此信号用于传送 Host的 command 和 Device 的 response。 DAT0-7 用于传输数据的 8 bit总线。 Host 与 eMMC之间的通信都是 Host 以一个 Command 开始发起的。针对不同的 Command,Device 会做出不同的响应。详细的通信协议相关内容,请参考2.3总线协议 章节。
mmc command. 目前Mboot支持以下mmc命令: 1) mmc read/write. 读写命令。Addr =内存地址,blk# =起始block数,size =需要读写的大小。 比如:#mmc read 0x50000000 0x400b 0x400000,表示从第0x400b块(0x400b*0x200 = 0x801600)处开始读0x400000 bytes大小数据到内存0x50000000。返回打印OK说明读成功。