Mitsubishi Electric Automation is proud to launch its FA Integrated Selection tool as a configuration resource for its customers. As opposed to digging through catalogs and manuals to select components that meet system requirements, the tool is designed to do this for customers in a user-friendly ...
*2 FX5CPU与远程起始模块不支持上述内容。 通过串行端口的连接 GX Works3 FX5-232ADP (1) FX5CPU GX Works3 (1) FX5UCPU/FX5UJCPU (FX5-232-BD) 产品名 型号 制造商名 (1)RS-232电缆 FX-232CAB-1 三菱电机株式会社 RCPU与远程起始模块不支持上述内容。 1 使用之前 44 1.9 计算机与CPU模块间...
MITSUBISHI三菱FX Configurator-FP 操作手册.pdf,FX Configurator-FP 操作手册 安全方面注意事项 (使用之前请务必阅读) 在安装、运行、保养·检查本产品之前,请务必仔细阅读本适用说明书以及其他相关设备的所有附带资料,正 确使用。请在熟悉了所有关于设备的指示、安全
Tool change position G30.1 G30.1 G30.1 G30.1 00 return 1 Tool change position G30.2 G30.2 00 return 2 Tool change position G30.3 G30.3 00 return 3 Tool change position G30.4 G30.4 00 return 4 Tool change position G30.5 G30.5 00 return 5 Skip function / G31 G31 G31 G31 00 ...
diagrams and explanations which will guide the reader in the correct installation and operation of the FX1N Series Programmable Controllers. It should be read and understood before attempting to install or use the unit. • Further information can be found in the FX Series Programming Manual II. ...
MITSUBISHI三菱Q170MCPU用户手册.pdf,SAFETY PRECAUTIONS (Please read these instructions before using this equipment.) Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to
(FXCPU)15 - 65 15.10.5 计算存储器容量时的注意事项15 - 66 15.11 存储卡的数据写入/ 读取 15 - 67 15.11.1 ATA卡/SRAM 卡/SD 存储卡的数据写入 /读取 15 - 68 15.11.2 SD存储卡的数据写入 /读取 (支持批量保存/ 载入功能)15 - 71 15.12 局部软元件的数据的读取 15 - 73 16 数据的保护 16.1...
If the battery low warning is issued, save the machining programs, tool data and parameters with an input/output unit, and then replace the battery. Do not short circuit, charge, overheat, incinerate or disassemble the battery. (7) Disposal Treat this unit as general industrial waste. Note ...
K Designation 275 12.4.5 Interrupts during Tool Nose Radius Compensation 280 12.4.6 General Precautions for Tool Nose Radius Compensation 282 12.4.7 Interference Check 283 12.5 Compensation Data Input by Program; G10, G11 288 12.6 Tool Life Management II 291 12.6.1 Counting the Tool Life 294 ...
4 Stopping characteristics 11-5 11-5 Capacity selection 11-6 11-6 Load torque equations 11-8 11-7 Load inertia moment equations 11-9 11-8 Precautions for zeroing 11-10 11-9 Selection example 11-11 iii CHAPTER 1 INTRODUCTION This chapter provides basic information needed to use this servo....