Monitor port: FortyGigE1/0/2 Mirroring group 2: Type: Local Status: Active Mirroring port: FortyGigE1/0/5 Inbound Monitor port: FortyGigE1/0/6 Encapsulation: Destination IP address 1.1.1.1 Source IP address 2.2.2.2 DSCP 1 VLAN 2 VRF Instance 3 Destination MAC address 0011-0200-0211 Table...
这条命令用于将名为monitor-port的监控端口加入到之前创建的mirroring group 1中,以便对该端口进行流量镜像操作。 3. 配置监控端口的流量镜像规则: ```bash kubectl create mirrorrule mirroring-group1 monitor-port ``` 这条命令用于创建一个流量镜像规则,将mirroring group 1中的流量镜像到名为monitor-port的端口...
E mirroring-group 1 monitor-port GigabitEthernet1 /0/22 正确答案 点击免费查看答案 试题上传试题纠错 猜您对下面的试题感兴趣:点击查看更多与本题相关的试题 在同一 交换机上,可以同时创建多个端口镜像,以实现对不同VLAN中的端口进行监听监听口与被监听口必须处于同一 个VLAN中 ...
MAC address mirroring is a more accurate mirroring mode, allowing you to monitor packets of a specified device for analysis. In Figure 1, the switch copies only the packets sent from HostB to the monitoring device. Similar to port mirroring, traffic mirroring is classified into local traffic ...
monitor port: GigabitEthernet4/3/1 mirroring-group 6: type: remote-source status: inactive mirroring port: GigabitEthernet4/3/4 inbound reflector port: GigabitEthernet4/2/4 remote-probe vlan: mirroring-group 9: type: remote-destination
使用S12500系列交换机配置本地端口镜像或远程镜像时提示Error: Local mirroring-group number exceeds hardware capability.[S12500-2]mirroring-group 2 local [S12500-2]mirroring-group 2 mirroring-port GigabitEthernet 2/0/23 both [S12500-2]mirroring-group 2 monitor-port GigabitEthernet 2/0/21 Error...
显示接口上的收发器 端口镜像: ]mirroring-group...1 local 创建本地镜像组 ]mirroring-gourp 1 mirroring-port g0/0 both 为镜像组配置源端口 ]mirroring-group 1 monitor-port...g0/1 为镜像组指定目的端口 ]display mirroring-group all 显示镜像组设置 VLAN技术:统一标准是802.1q,它是在标准帧的MAC地址后...
switch(config)#monitor session r1 source Ethernet2 rx ip access-group a3 switch(config)#monitor session r1 destination tunnel mode gre source 75.75.75.75 destination 100.1.0.2 Displaying Mirroring with Greenspan and Port Information These two commands display the monitor and platform related mirroring ...
Although compactflash: can be used as the secondary device on a Performance Route Processor (PRP–2), there’s an issue with the ROM Monitor not being able to boot the minimum boot image (MBI) from the secondary device if the device isn’t...
Each source port can be configured with a direction (ingress) to monitor. For bundles, the monitored direction applies to all physical ports in the group. Figure 3. Network Analysis on a Router with Traffic Mirroring In the figure above,...