● Backup RouterBOOT 1) Power device off, press and hold the reset button 2) Power device on and after 1-2 seconds release the button ● Netinstall 1) Test Netinstall https://wiki.mikrotik.com/wiki/Manual:Netinstall 2) Try to re-install any other router ● Reset device https://wiki.mi...
VLAN- IEEE802.1q Virtual LAN,支持以太网和无线连接;多VLAN支持;VLAN桥接。 Synchronous- V.35, V.24, E1/T1, X.21, DS3 (T3)媒体类型; sync-PPP, Cisco HDLC, 帧中继协议; ANSI-617d (ANDI or annex D)和Q933a (CCITT or annex A) 帧中继LMI类型 Asynchronous– 串型PPP dial-in / dial-out;...
VLAN- IEEE802.1q Virtual LAN,支持以太网和无线连接;多VLAN支持;VLAN桥接。 Synchronous- V.35, V.24, E1/T1, X.21, DS3 (T3)媒体类型; sync-PPP, Cisco HDLC, 帧中继协议; ANSI-617d (ANDI or annex D)和Q933a (CCITT or annex A) 帧中继LMI类型 Asynchronous– 串型PPP dial-in / dial-out;...
VLAN- IEEE802.1q Virtual LAN,支持以太网和无线连接;多VLAN支持;VLAN桥接。 Synchronous- V.35, V.24, E1/T1, X.21, DS3 (T3)媒体类型; sync-PPP, Cisco HDLC, 帧中继协议; ANSI-617d (ANDI or annex D)和Q933a (CCITT or annex A) 帧中继LMI类型 Asynchronous– 串型PPP dial-in / dial-out;...
5005上的esxi经历过6.0和6.5,之前提到过 “把lan出口和Management Network连在一起”,就是因为血的教训搞坏了拓扑,连不上esxi, 一横心重装了个6.5。esxi上的usb3.0支持在6.0的时候是正常的,到了6.5他们统一了usb驱动,结果6.5里边usb3的设备会连到usb2的总线上,下图中Bus 001是usb3的总线,esxi赢把所有设备连...
指的是tilera系列芯片本身，和FP，FT没关系 router os的tilera也有硬件加速的驱动，支持硬件offload ...
Now you might need to allow connections from the ZeroTier interface to your router, andoptionally, to your other LAN interfaces: /ip firewall filter add action=accept chain=forward in-interface=zerotier1 place-before=0 /ip firewall filter add action=accept chain=input in-interface=zerotier1 ...
r - reset all router configuration + l - load interface driver * a - configure ip address and gateway d - setup dhcp client s - setup dhcp server p - setup pppoe client t - setup pptp client x - exit menu your choice [press Enter to configure ip address and gateway]: a 配置IP...
Step 2:IP > Routes > Gateway + = such as( 192.168.0.1 ) > Apply > OK MikroTik DNS configure: Step 3:IP > DNS > DNS Settings > servers= 203.122.120.2 = 203.122.120.3 = 8.8.8.8 LAN Site configure ( Step1-Step3) Step 1.winbox open: IP > Address + address =such as( 10.10.0.1...
Specifies if peer is intended to be connection initiator or only responder. Should be used on WireGuard devices that are used as "servers" for other devices as clients to connect to. Otherwise router will all repeatedly try to connect "endpoint-address" or "current-endpoint-address". ...