/ip dhcp-clientaddcomment="default configuration"dhcp-options=hostname,clientidinterface=ether01 1. 2. 7 外网口配置 7.1 PPPOE拨号配置 /interface pppoe-clientaddac-name=""add-default-route=yesallow=pap,chap,mschap1,mschap2\default-route-distance=1dial-on-demand=yesdisabled=nointerface=ether01\k...
--- 1.首先将路由器的Ethernet口和所有要使用的串口都激活,方法是进入该口,执行No Shutdown。 --- 2.将和路由器相连的主机加上缺省路由(中心路由器的Ethernet地址),方法是在UNIX系统的超级用户下执行:router add defaule XXXX 1(XXXX为路由器的E0口地址)。每台主机都要加缺省路由,否则,将不能正常通讯。 -...
wine = winbox.exe neighbourhood 192.168.50.1 (LTE) - admin, no passwd /interface lte apn add name=ETC apn=etc.com /interface lte set network-mode=3g,lte lte1% in user interface, set modus to 3G,LTE %# inbetween /interface lte info lte1 => EGPRS :-(Test if devices can ...
power-cycle-ping-enabled(yes | no; Default:no)Enables ping watchdog, power-cycles port if a host does not respond to ICMP or MAC-Telnet packets. power-cycle-ping-address(IPv4 | IPv6 | MAC; Default: )An address which will be monitored. Since RouterOS 6.46beta16, an active route towards...
上回介绍了在vultr安装了routerOS,本文在前文基础上分享如何在routerOS中使用docker,自从router7.X版本开始,routerOS支持运行docker,但只支持CPU架构ARM和X86,这极大的扩展了routerOS的功能……一直以来我只是在VPS上使用routerOS,而曾经我需要专门使用一台服务器跑routerOS,然后再用另一台服务器跑其它各种应用,从经济上就...
/interface pppoe-client add add-default-route=yes interface=vlan10-internet keepalive-timeout=disabled name=pppoe-out1 password=*** user=*** 确认接口都已经创建,然后monitor一下,确定PPPoE已经正确连接。 [terry@MikroTik] /interface/pppoe-client> monitor 0 status: connected...
ip6-6plane( yes | no; Default:no)An optiongives every member a /80 within a /40 network but uses NDP emulation to routeallIPs under that /80 to their owner. The6planemode is great for use cases like Docker since it allows every member to assign IPv6 addresses within its /80 that ...
1 (LAN) to (WAN) source dynamic any interface translate_hits = 767, untranslate_hits = 62 (TEST) to (WAN) source static NETWORK_OBJ_10.6.0.0_24 NETWORK_OBJ_10.6.0.0_24 destination static NETWORK_OBJ_10.7.0.0_24 NETWORK_OBJ_10.7.0.0_24 no-proxy-arp route-lookup translate_hits = 0,...
add comment="default configuration"dhcp-options=hostname,clientid interface=ether01 7 外网口配置 7.1 PPPOE拨号配置 1 2 3 4 5 6 /interfacepppoe-client add ac-name=""add-default-route=yesallow=pap,chap,mschap1,mschap2 \ default-route-distance=1 dial-on-demand=yesdisabled=no interface=ether...
[find] will show additional fields: power-cycle-host-alive: <YES/NO> (Shows if monitored host is reachable) power-cycle-after:<TIME> (Shows time, after which the port will be power-cycled) ===SNMP=== It is possible to monitor PoE-Out values using SNMP protocol, this requires...