之后还需在ip firewall mangle中添加一条规则: [admin@Router] ip firewall mangle> add chain=forward protocol=tcp tcp-flags=syn action=change-mss new-mss=1440 [admin@Router] ip firewall mangle> print Flags: X - disabled, I – invalid 0 chain=forward protocol=tcp tcp-flags=syn action=change...
端口映射 这里我们需要将内网的http 服务器发布到外网,内网的http 服务器ip 地8 这里需要做端口映射规则,进入ip firewall nat 里,选择chain=dstnat,我们的外网ip 26、 地址是17 配置到dst-address,dst-port 为tcp 协议80 端口,如下图: 在 action 选择dst-nat 操作,to-address 设置内网http 服务器ip 地址,...
Move the rule to the top.GregSowell.comIPSec Tunnel – MTK to MTK - Site # 2Create Peer Create Policy Create/ModifyProposal if you choose GregSowell.comIPSec Tunnel – MTK to MTK - Site # 2 IP -> Firewall -> NAT Create NAT bypass for traffic that should traverse the tunnel. Move ...
[admin@Router] interface pppoe-client>enable 0 [admin@Router] interface pppoe-client> monitor pppoe-out1 status: "connected" uptime: 10s encoding: "none" service-name: "CHN-Telecom" ac-name: "" ac-mac: 00:C0:DF:07:5E:E6 之后还需在ip firewall mangle中添加一条规则: [admin@Router] ip...
MikroTik RouterOS v2.9 基本操作说明 CDNAT RouterOS应用说明主要特征 TCP/IP协议组: Firewall和NAT – 包状态过滤;P2P协议过滤;源和目标NAT;对源MAC、IP地址、端口、IP协议、协议(ICMP、TCP、MSS等)、接口、对内部的数据包和连接作标记、ToS 字节、内容过滤、顺序优先与数据频繁和时间控制、包长度控制... 路由...
软路由MikroTik RouterOS 简明教程配置过程见附图.pdf,软路由MikroTik RouterOS 简明教程配置过程见附图 命令说明: RouterOS 的基本设置包括四个部分interface、ip address、ip route 、ip firewall src-nat。 1.interface 的命令中主要为修改接口称和激活接口; 2.ip addr
/ip firewall rule input add protocol=icmp comment="Allow ICMP Ping" /ip firewall rule input add src-address=192.168.0.0/24 \ comment="From my home network" /ip firewall rule input add action=drop log=yes \ comment="Log and drop everything else" (可选)配置DHCP服务散发IP配置到你的家庭...
1.interface命令中主要为修改接口称与激活接口;2.ipaddress命令主要为分别在两接 相应接口上增加外网IP地址与局域网IP地址;3.iproute命令主要是墙加路由表,这 里简单网络路由表中只有三条,一条是手动加,两条是动态路由项;4.ipfirewallsrc- nat命令是用来设置网络地址转换,这里伪装masquerade)即是网络地址转换NAT)...
===IPv4 firewall to a router=== * work with new connections to decrease load on a router; * create address-list for IP addresses, that are allowed to access your router; * enable ICMP access (optionally); * drop everything else, log=yes might be added to log packets that hit the ...
[admin@MikroTik] ip route> /ping 10.0.0.1 10.0.0.1 ping timeout 2 packets transmitted, 0 packets received, 100% packet loss [admin@MikroTik] ip firewall nat> .. service-port print Flags: X - disabled, I - invalid # NAME PORTS 0 ftp 21 1 tftp 69 2 irc 6667 3 h323 4 sip 5 ppt...