齐护Arduino及Micropython蓝牙编程通用上传器,可用于Arduino UNO或328芯片的所有开发板及ESP或K210的Micropython编程软件或APP上传。 # 2,windows电脑的连接方法 下面我们介绍windows电脑的连接方式,首先我们把蓝牙上传器通上电,确认蓝灯在闪烁,在蓝牙区右键,打开添加蓝牙设备,如果是windows11那么请打开在蓝牙设备发现中设置...
ESP-IDF SoftWare Serial 基于该项目 Github ArduinoEsp32-SoftwareSerial。 花了点时间写了一下软串口,因为娱乐和工程需要,所以我从过去自己在 Arduino 上实现的软串口移植到 ESP-IDF 下,为此也写一周了吧,使用硬件为 Bpi:Uno (esp32)。 更新了一次 esp8266 rtos 用的软串口,大概只做到了 57600 这个范围内稳...
如果再和我自己设计的Arduino uno/nano转接板相结合,将大大提升性能(以前只能用软件模拟,现在用PIO直接硬驱!上了一个台阶!) 后面我会重点收集这方面的知识和程序,全面展示pio的用法。希望用pio把常见的通信接口全部模拟一遍(pwm, spi, i2c, uart, i2s, qspi, sdio, usb,1-wire等等),再把手头的十几个模块,...
RA4M1Arm Cortex®-M4 / RA4M132-bitCortex®-M4 processor https://www.arduino.cc/UNOR4 RP2040Dual ARM Cortex-M0+ / Dual ARM Cortex-M0+ @133MHz https://www.raspberrypi.com/documentation/microcontrollers/rp2040.html Raspberry PiPico https://www.raspberrypi.com/products/ Powerful, flexible...
Arduino Nano/Uno 支持 不支持 ESP32 支持 支持 STM32 支持 支持 开发注意事项 使用Arduino IDE除了Nano/Uno外,Raspberrypi Pico、ESP32和STM32都需要安装对应的环境。 使用MicroPython需要预先烧录MicroPython固件。 使用Arduino IDE开发和使用MicroPython所使用的可能引脚不同,按需要修改。 环境安装方法百度有很多,实在...
wlan.scan() # scanforaccesspoints wlan.isconnected() #checkifthe stationisconnectedtoan AP wlan.connect('ssid','key') #connecttoan AP wlan.config('mac') #getthe interface's MACaddress wlan.ifconfig() # get the interface's IP/netmask/gw/DNS addresses ...
http:// docs.micropython.org/en/latest/esp8266/。 要使诊断信息包含在错误报告中,请执行“ import port_diag ”。 sta_if = network.WLAN(network.STA_IF) sta_if.active(True) sta_if.scan() # Scan for available access points sta_if.connect("", "") # Connect to an AP ...
Github ArduinoEsp32-SoftwareSerial 花了点时间写了一下软串口,因为娱乐和工程需要,所以我从过去自己在 Arduino 上实现的软串口移植到 ESP-IDF 下,为此也写一周了吧,使用硬件为 Bpi:Uno (esp32)。 更新了一次 esp8266 rtos 用的软串口,大概只做到了 57600 这个范围内稳定使用,但开头总有一两个字节要出错,应...
AMB21/AMB22 and Arduino Uno have similar size, as shown in the above figure, and the pins on AMB21/AMB22 are compatible with Arduino Uno. AMB21/AMB22 uses Micro USB to supply power, which is common in many smart devices. Please refer to the following figure and table for the pin di...
You’ll need a suitably-sized resistor, such as a 220ohm resistor. You’ll need to connect that to the ground and to the short leg of your LED. The positive, long leg of your LED will connect to the GPIO pin 2. On the Wemos D1 Uno board, GPIO 2 is called Digital Pin 9 on ...