http://download3.dfrobot.com.cn/uPyCraft/uPyCraft.exe 这是一个直接运行的程序,双击运行,出现一个字体缺失的提升,点 Cancel 即可。 3.1.烧写 Tool,BurnFirmware,打开新弹窗, Board 选择 esp8266, erase_flash 选择 yes, com选择设备管理器中看到的 COM3, FirmwarChoos
ESP8266 NODEMCU官方网站http://www.nodemcu.com/index_cn.html 固件下载地址https://github.com/nodemcu/nodemcu-firmware/releasesNODEMCU一键烧录软件下载地址https://github.com/nodemcu/nodemcu-flasherESP8266模块最小系统接线后,将GPIO0接GND 智能推荐
# 清空flash esptool --port COM18 erase_flash # 烧录固件 esptool --port COM18 --baud 115200 write_flash --flash_size=detect 0 esp8266-20190125-v1.10.bin 烧录完成,使用putty或者SecureCRT连接 如果连接能显示 说明安装成功。 如果提示 1 2 Can't autodetect firmware, because proper answer not re...
从MicroPython网站Download选择 ESP8266-20210202-V1.14bin文件下载到本地计算机目录下。 使用这个软件的 ESP8266 Firmware Installer 对ESP8266-01S进行软件更新。下面是更换过程,但是出现固件下载错误。 工作模式下出现下载错误 下面是在Thonny下载界面信息框中给出的出错信息。显示了Thonny无法发送芯片擦除命令。 根据 图...
Download File Copy Code wlan.ifconfig() Notice the first result from the ifconfig call is the IP address assigned to the ESP8266 (192.168.1.207 in this example, but it will differ depending on your WiFi network). If you don't see an IP address then something is wrong with the WiFi co...
ESP-01S 如图 软件 Thonny AiThinker_Serial_Tool_V1.2.3 flash_download_tools_v3.6.8 esp8266-20190529-v1.11.bin 概要 经历了很长很长很长很长的时间,跳过了各种坑,终于,在居家隔离的日子里,把这个项目搞定了 首先呢,淘宝购买了设备,先用 Raspberry pi RP 连接ESP01S、控制继电器,联网,控制电器,发现硬件...
2.ESPFlashDownloadTool_v3.3.4TPYBoardv202固件烧写工具 下载地址:http://www.tpyboard.com/download/tool/185.html 3.第三方库文件:micropython-lib\umqtt.simple\umqtt\simple.py 下载地址:http://www.tpyboard.com/download/data/184.html 4.TPYBoardv202固件 ...
Note that the default I2C pins on the ESP8266 board are D1 (SCL) and D2 (SDA). However, we can use any output-capable GPIO on ESP8266 for SDA and SCL lines. We have chosen D0 for SCL and D1 for SDA. Note that you must have uploaded MicroPython firmware to ESP8266 and get uP...
This will follow by erasing the flash memory on ESP8266 and uploading the MicroPython firmware. If you see an error shown in the image below, ESP8266 is not the boot mode. You did not press the boot/flash button properly. Repeat the above process from selecting a port to burning firmware...
If you want to program your ESP32 and ESP8266 with MicroPython firmware, it’s very handy to use an IDE. In this guide, we’ll introduce you to Thonny IDE.