the processor determines transmission power based on a configured Maximum Power Reduction (MPR), and the MPR is edge RB allocations, outer RB allocations and Inner RB allocations, the MPR is set based on DFT-s-OFDM and CP-OFDM, and the MPR is set based on Pi/2 BPSK, QPSK, 16 QAM, ...
MaxRB2: Fc_aggregation: MHz BW_Channel_CA: MHz Outputs F_agg_alloc_Low: MHz F_agg_alloc_High: MHz A: ΔIM5: MA: M_IM5: Max. Pwr. Reduction dB 所使用的公式 针对支持非连续资源分配的C类带间连续载波带宽,在最大输出功率条件下允许的最大功耗降幅(MPR)指定如下 ...
附件C.2中规定了PDSCH和PDCCH在测量前的配置。 Table 6.2.2.4.1-1: Test Configuration Table (Power Class 1, MPRnarrow) Default Conditions Test Environment as specified in TS 38.508-1 [10] subclause 4.1 Normal Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1 Low range, High...
Under previous standards using one carrier, the maximum power reduction (MPR) needed to address those issues could be stored on the device, since the total number of MPR values was limited. With the introduction of dual carriers in HSUPA-9, storing all possible MPR values is no longer ...
For intra-band contiguous carrier aggregation bandwidth class D with non-contiguous resource allocation, the allowed Maximum Power Reduction (MPR) for the maximum output power in Table 6.2.3A-2 is specified as follows: MPR = CEIL {min(MA, MIM5), 0.5} ...
Determining maximum power reduction (MPR) for multi-cluster wireless transmissions 来自 百度文库 喜欢 0 阅读量: 21 申请(专利)号: US201314043648 申请日期: 2013-10-01 公开/公告号: US2014092838A1 公开/公告日期: 2014-04-03 申请(专利权)人: QUALCOMM INCORPORATED ...
6.2.2UE maximum output power reduction-翻译 1、测试目的 6.2.2.3中确定的RB数量是基于满足立方米制(CM)的最大功率回退(MPR)的要求。 2、测试适用 本测试要求适用于所有类型的NR UE release 15和forward。 3、测试说明 1、初始条件 初始条件是UE需要测试的一组测试配置,以及SS为使UE达到正确的测量状态而采取...
6.2.2UE maximum output power reduction-翻译 【摘要】 1、测试目的 6.2.2.3中确定的RB数量是基于满足立方米制(CM)的最大功率回退(MPR)的要求。 2、测试适用 本测试要求适用于所有类型的NR UE release 15和forward。 3、测试说明 1、初始条件 初始条件是UE需要测试的一组测试配置,以及SS为使UE达到正确的测量...
In radio frequency (RF) power amplifiers (PA), power efficiency, linearity and cost are contradictory requirements. In the Long Term Evolution (LTE) and LTE-Advanced (LTE-A) standards by the Third Generation Partnership Project, maximum power reduction (MPR) is used to relax RF PA requirements...
For intra-band contiguous carrier bandwidth class C with non-contiguous resource allocation, the allowed Maximum Power Reduction (MPR) for the maximum power output power is specified as follows MPR = CEIL {min(MA, MIM5), 0.5} Where MAis defined as follows for QPSK, 16 QAM and 64 QAM:...