可以看到TCPserver变量所具有的属性。当有TCPClient接入时,”Connected“属性会显示为接入的Client的数量,未有Client接入则为零。 2.注意上图中的“NumBytesAvailable”属性,这一属性代表当前通信状态下的数据字节数。在下一小节中,该属性将作为标准判断是否可以读取数据。 1.3 配置数据读取模式并编写回调函数 1.在下位...
Check IDSeverityMessageMessage ReleaseCan Be Disabled?Related Documentation TMMSG Error More than 10,000 Code Analyzer messages were generated, leading to some being deleted. false TMSMS Error More than 1,000 parse error messages were generated, leading to some being deleted. false MXASET Error...
使用configureCallback 函数为与远程主机的通信设置回调函数和触发条件。使用flush 函数刷新缓冲区,以便与远程主机通信。通过创建一个连接到 TCP/IP 回显服务器的 tcpclient 对象、向其写入数据和从中读取数据,开始使用 TCP/IP 客户端接口。echotcpip("on",3030)t = tcpclient("localhost",3030)write(t,1:5,"uin...
flush 清空串行端口设备缓冲区 getpinstatus 获取串行引脚状态 setRTS 设置串行 RTS 引脚 setDTR 设置串行 DTR 引脚 TCP/IP 通信 - 连接和配置 :-:- tcpclient 创建与 TCP/IP 服务器的 TCP/IP 客户端连接 echotcpip 启动或停止 TCP/IP 回显服务器 configureTerminator 为通过 TCP/IP 与远程主机进行的 ASCII...
tcpclient, read, and write Functions: Generate C and C++ code The tcpclient, read, and write functions support C and C++ code generation using MATLAB Coder. Bluetooth Low Energy Interface: Support for scanning and interacting with peripheral devices You can us...
flush 清空串行端口设备缓冲区 getpinstatus 获取串行引脚状态 setRTS 设置串行 RTS 引脚 setDTR 设置串行 DTR 引脚 TCP/IP 通信 - 连接和配置 :-:- tcpclient 创建与 TCP/IP 服务器的 TCP/IP 客户端连接 echotcpip 启动或停止 TCP/IP 回显服务器 configureTerminator 为通过 TCP/IP 与远程主机进行的 ASCII...
flush 清空串行端口设备缓冲区 getpinstatus 获取串行引脚状态 setRTS 设置串行 RTS 引脚 setDTR 设置串行 DTR 引脚 TCP/IP 通信 - 连接和配置 tcpclient 创建与 TCP/IP 服务器的 TCP/IP 客户端连接 echotcpip 启动或停止 TCP/IP 回显服务器 configureTerminator 为通过 TCP/IP 与远程主机进行的 ASCII 字符串...
flush 清空串行端口设备缓冲区 getpinstatus 获取串行引脚状态 setRTS 设置串行 RTS 引脚 setDTR 设置串行 DTR 引脚 TCP/IP 通信 - 连接和配置 tcpclient 创建与 TCP/IP 服务器的 TCP/IP 客户端连接 echotcpip 启动或停止 TCP/IP 回显服务器 configureTerminator 为通过 TCP/IP 与远程主机进行的 ASCII 字符串...
flush 清空串行端口设备缓冲区 getpinstatus 获取串行引脚状态 setRTS 设置串行 RTS 引脚 setDTR 设置串行 DTR 引脚 TCP/IP 通信 - 连接和配置 tcpclient 创建与 TCP/IP 服务器的 TCP/IP 客户端连接 echotcpip 启动或停止 TCP/IP 回显服务器 configureTerminator 为通过 TCP/IP 与远程主机进行的 ASCII 字符串...
flush 清空串行端口设备缓冲区 getpinstatus 获取串行引脚状态 setRTS 设置串行 RTS 引脚 setDTR 设置串行 DTR 引脚 TCP/IP 通信 - 连接和配置 :-:- tcpclient 创建与 TCP/IP 服务器的 TCP/IP 客户端连接 echotcpip 启动或停止 TCP/IP 回显服务器 configureTerminator 为通过 TCP/IP 与远程主机进行的 ...