一、添加SW开关 打开LTspice软件,进入原理图编辑界面。 在工具栏中点击“组件”按钮,或者在键盘上按F2键打开组件库。 在搜索字段中输入“sw”,找到电压控制开关SW的符号,点击选择并添加到原理图中。 二、设置SW开关属性 右键单击原理图中的SW开关符号。 在弹出的属性窗口中,找到“值”或“spicemodel”字段(具体字...
.model MYSW SW(Ron=1 Roff=1Meg Vt=.5 Vh=-.4), 其中“MYSW”是唯一的型号名称,Ron 和 Roff 是导通和关断电阻,Vt 和 Vh 是跳闸和迟滞电压。开关在 (Vt − Vh) 和 (Vt + Vh) 处跳闸。 LTspice帮助(按F1)包含有关SW模型参数的更多信息。 将MYSW 型号分配给开关符号 S1:右键单击“SW”并输...
定义参数:.paramswitch_on 10 定义模型:.modelSW SW(Ron=1 Roff=1Meg Vt=.5 Vh=-.4) 2. 基本操作 LTspice的tricks: you first select the action and then the object Right click once to cancel the current wire You can draw wires through components such as resistors. The wire will automaticall...
.modelSW-VoltSW(Roff=1G Ron=25u Vt=0.1Vh=0.1) 这个开关关联上一个交变电源或者脉冲电源就可以模拟开关动作了. Roff代表off时的阻值, Ron代表on时的阻值, Vt代表 trigger voltage(触发电压), Vh代表 hysteresis on the trigger voltage (触发电压滞后). 参考 添加新元件的方式(临时, 引用, 添加到库)https...
.model MySwitch SW(Ron=1m Roff=1Meg Vt=1) 用1mOhm 的导通电阻、1MOhm 的关断电阻和 1V 的阈值电压来表征开关。我们不需要其他特征。 将文本放置在原理图上的任意位置。 要将开关与我们刚刚定义的 .model 相关联,请右键单击原理图窗口中的开关符号。在Value字段中输入MySwitch,将.model定义与开关关联,如图...
near regulation (or at a known time), all the SMPS output energy goes into charging up the large output capacitors prior to the load being applied. The startup and the main load resistance can also be encapsulated in Ron and Roff of the SW model statement rather than using seperate ...
图6. Venable System Model 5060A老式网络分析仪,用于高边浮动噪声注入和LED驱动器的测量。 图7. LT3950 LED驱动器上的噪声注入和测量点。 图8. DC2788A演示电路板上的LT3950 LED驱动器的波德图。通过LTspice模拟生成的图(蓝线)与使用网络分析仪生成的图(绿线)相关性强。
.MODEL N NMOS LEVEL=1 VTO=0.7 GAMMA=0.45 PHI=0.9 +NSUB=9e14 LD=0.08e-6 UO=350 LAMBDA=0.1 +TOX=9e-9 PB=0.9 CJ=0.56e-3 CJSW=0.35e-11 +MJ=0.45 MJSW=0.2 CGDO=0.4e-9 JS=1.0e-8 其中所有参数的名称如下: VTO: threshold voltage with zero VSB (unit: V) ...
LTspice Help (press F1) contains more about the SW model parameters. Assign the MYSW model to the switch symbol S1: right-click “SW” and enter the unique model name, “MYSW”. Control the switch with a voltage source connected to the positive terminal of the switch and ground the neg...
以【.model】定义的spice模型基本都可以按这种方式进行导入并使用,比如二三极管、MOS等。 这种方式局限性较大,比如不适合将仿真原理图给到别人进行仿真,因为别人的库里面没有你需要的文件;另外,更新库的时候也会被覆盖掉。因此不建议使用这种方式。 2. 直接粘贴模型到原理图 ...