arduino-LoRa(简单好用,封装配置) 最终选用的是arduino-LoRa,使用RadioLib在实现双向通行上遇到问题(C++功力不够)。 arduino-LoRa最大的好处就是简化了很多芯片参数的配置,如果业余选手要配置好参数能够实现两个模块通信是个艰巨的挑战,这也是串口Lora模块的优势,不用去关心复杂的通信参数配置。 阅读arduino-LoR
我使用一个Arduino Nano 来驱动Lora模块,另外加了一个BMP085(I2C接口)气压传感器,一个光敏电阻,一个按钮。 使用PlantformIO平台开发。(比Arduino IDE好用很多) 实现功能有: 参考arduino-LoRa双向通行的自有简单协议; 获取传感器的温度,气压数据,光亮度; 获取供电电池电压; 定时通过Lora发送数据,按键强制发送一条数据...
我使用一个Arduino Nano 来驱动Lora模块,另外加了一个BMP085(I2C接口)气压传感器,一个光敏电阻,一个按钮。 使用PlantformIO平台开发。(比Arduino IDE好用很多) 实现功能有: 参考arduino-LoRa双向通行的自有简单协议; 获取传感器的温度,气压数据,光亮度; 获取供电电池电压; 定时通过Lora发送数据,按键强制发送一条数据;...
nano https://www.electroniclinic.com/arduino-and-lora-based-automation-project-with-feedback-message-lora-sx1278/ 发射板 3d图 发射 接收板 3d 接收 发射部分用了一个透明防水盒和四个自锁开关,每个开关控制一路继电器,可以外接电源或者充电宝供电,显示屏用的ssd1306,每一路的开关由0或1指示。接收部分用...
LoRa 基本模块原型 PCB 基本上是一个 Arduino Nano 风格的 PCB(就 IO 而言),在 SPI 线路(SCK、MISO、MOSI、SS)上具有电平转换以及 Lora 复位和 IRQ 引脚(这对于唤醒至关重要稍后启动处理器)。 由于原型将主要用于实验室,后续才会进行一些户外测试,因此未提供电池充电电路。两个 LDO 稳压器 5v 和 3.3v 从 ...
Arduino MKR WAN 1300 NOTE:Requires firmware v1.1.6 or later on the on-board Murata module. Please use theMKRWANFWUpdate_standalone examplefrom latestMKRWAN libraryrelease to update the firmware. WARNING:LoRa.onReceive(...)andLoRa.recieve()is not compatible with this board!
2021-12-22 1.0.1 Fix on keywork and change DEBUG_PRINTLN on example with Serial And tested Arduino MKR WiFi 1010 and Arduino Nano 33 IoT https://downloads.arduino.cc/libraries/logs/github.com/xreef/EByte_LoRa_E22_Series_Library/
Arduino library “ArduinoJson” installed 1. Set Up the Module Acting as Gateway Connect the ESP32 or ESP8266 module to the Wio-E5 Groove module in the following way: If you are using Wio-E5 mini: Connect the ESP32’s“RX”terminal to“TX”on the LoRa-E5 mini (the one with the ...
使用Arduino Nano驱动Lora模块为什么选用Lora射频通信芯片有很多种,但是一般在同样功耗下,距离没有Lora远;同等范围下,没有Lora节能。 Lora通信只适用于低速率,高延时的场合,与WiFi正好相反。考虑在野外,没有移动通信网络覆盖的环境下,收集传感器数据,适合使用。在设密度大,使用移动通信网络成本过高,使用Lora来统一收集数...
In this case check the free memory in Arduino IDE. Custom sensors If you need you can add any sensors and then see its values in the application. To do this, just edit the section with the main data structure and the section with the protocol. Note that all software versions must be ...