1. 固定一个MAC地址,特别是在使用多个虚拟机的时候 linux环境下: 用root身份登录,在/etc/rc.d/rc.local里加上这三句 ifconfig eth0 down ifconfig eth0 hw ether 00:0C:18:EF:FF:ED ifconfig eth0 up 这样重新reboot后就不怕MAC复原了。 2. ifconfig命令 ifconfig [Interface] Interface是可选项,如...
ifconfig [interface] hw ether [new mac address] “` 将”[interface]”替换为要设置的网络接口的名称,将”[new mac address]”替换为新的MAC地址。例如,设置eth0接口的MAC地址为00:11:22:33:44:55的命令如下: “` ifconfig eth0 hw ether 00:11:22:33:44:55 “` 4. 使用以下命令验证MAC地址是否...
重启网络接口使更改生效:sudo ifconfig eth0 down然后sudo ifconfig eth0 up 使用ip命令(较新版本Linux) 查看当前网络接口信息:ip link show eth0 修改MAC地址:sudo ip link set dev eth0 address XX:XX:XX:XX:XX:XX 重启网络接口使更改生效:sudo ip link set dev eth0 down然后sudo ip link set dev ...
set_master_hwaddr(master_ifname,&(slave_hwaddr.ifr_hwaddr))->ioctl(skfd,SIOCSIFHWADDR,&ifr)->dev_ifsioc(net,&ifr,cmd)->dev_set_mac_address(dev,&ifr->ifr_hwaddr)->//设置网卡MAC地址dev->netdev_ops->ndo_set_mac_address(dev,&ifr->ifr_hwaddr);//最终调用net_device的ops成员函数实现...
1. 固定一个MAC地址,特别是在使用多个虚拟机的时候 linux环境下: 用root身份登录,在/etc/rc.d/rc.local里加上这三句 ifconfig eth0 down ifconfig eth0 hw ether 00:0C:18:EF:FF:ED ifconfig eth0 up 这样又一次reboot后就不怕MAC复原了。
ip命令是ifconfig的替代品,可以使用以下命令设置IP和MAC地址: “`shell ip addr add 192.168.1.100 dev eth0 # 设置eth0接口的IP地址为192.168.1.100 ip link set dev eth0 address 00:11:22:33:44:55 # 设置eth0接口的MAC地址为00:11:22:33:44:55 ...
例如,设置eth0接口的MAC地址为00:11:22:33:44:55: shell sudo ip link set dev eth0 address 00:11:22:33:44:55 输入命令以重启网卡: 设置完MAC地址后,需要重新启用网络接口以使更改生效。 shell sudo ifconfig <网卡接口名> up 例如,重新启用eth0接口: shell sudo ifconfig eth0 up 或者...
一般来说,直接输入 ifconfig 就会列出目前已经被启动的卡,不论这个卡是否有设置 IP,都会被显示出来。而如果是输入 ifconfig eth0,则会显示出这个接口的相关数据,而不管该接口是否启动。所以,如果你想要知道某个网卡的 Hardware Address,直接输入“ifconfig "网络接口代号"”即可。至于上述代码中出现的各项数据是这样...
rtnl_lock(); ret= dev_set_mac_address(jz_ndev,&hwaddr);//调用我们分析到的函数,来设置mac地址rtnl_unlock(); 6.3 编译-试验 启动后输入ifconfig,即可看到内核已经帮我设置好了: 总结:其实实现的代码很简单,但是需要去分析才能把东西消化为自己的....