链路速率(link speed): 链路速率是指InfiniBand网络中物理链路上的最大传输速率。它通常以Gbps(千兆比特每秒)为单位表示。 断开连接(disconnect): 断开连接是指在两个节点之间结束通信连接的过程,使得每个适配器和端口可以重新分配给其他节点。 常用命令 当前测试系统 root@liruilongs.github.io:~# hostnamectl Static...
语法:shapecfg attach [流量管制器][网络设备] 或 shapecfg speed [流量管制器][带宽] 补充说明:自Linux-2.15开始,便支持流量管制的功能。 参数: attach 将流量管制器与实际的网络设备结合。 speed 设置流量管制器的对外传输带宽。 smbd(samba daemon) 功能说明:Samba服务器程序。 语法:smbd [-aDhoP][-d<排错...
192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.6 在这个输出中,你可以看到通过eth0的默认网关是192.168.0.1,并且本地网络是相当标准的192.168.0.0/24。 你也可以使用ip命令来启用和禁用网络接口。 $ sudo ip link set eth1 up $ sudo ip link set eth1 down ethtool 命令 另一个检查网...
ethtoolis a replacement ofmii-tool. It is to view, setting speed and duplex of yourNetwork Interface Card(NIC). You can set duplex permanently in/etc/sysconfig/network-scripts/ifcfg-eth0withETHTOOL_OPTSvariable. # ethtool eth0Settings for eth0: Current message level: 0x00000007 (7) Link ...
If you’re using the ifupdown plugin (for example, in Ubuntu and Debian), add the interface configuration to your /etc/network/interfaces file and then set the value of managed to false in the ifupdown section of the NetworkManager.conf file: 您可以通过使用插件告诉NetworkManager忽略某个接口。
ethtool –s ethX [speed 10|100|1000] [duplex half|full] [autoneg on|off] //设置网口速率10/100/1000M、设置网口半/全双工、设置网口是否自协商 [root@natsha ~]# ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full ...
disk_set FLAG STATE change the FLAG on selected device disk_toggle [FLAG] toggle the state of FLAG on selected device set NUMBER FLAG STATE change the FLAG on partition NUMBER toggle [NUMBER [FLAG]] toggle the state of FLAG on partition NUMBER unit UNIT set the default unit to UNIT ...
[15:12 @ ~/program/netspeed]$ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:22:15:67:F8:16 inet addr:210.42.158.204 Bcast:210.42.158.255 Mask:255.255.255.0 inet6 addr: fe80::222:15ff:fe67:f816/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ...
ip link set dev eth0 mtu 1400 “` 该命令将eth0网卡的MTU大小设置为1400字节。 这些命令可以根据需要修改不同网卡的流量设置。需要注意的是,修改网卡的流量设置可能会对系统的网络性能产生影响,建议在进行修改前先进行测试和评估。 Worktile&PingCode市场小伙伴 ...
链路速率(link speed):链路速率是指InfiniBand网络中物理链路上的最大传输速率。它通常以Gbps(千兆比特每秒)为单位表示。 断开连接(disconnect):断开连接是指在两个节点之间结束通信连接的过程,使得每个适配器和端口可以重新分配给其他节点。 常用命令 当前测试系统 ...