PPS_FETCH:用于从PPS设备获取事件数据。用户空间程序可以通过这个ioctl调用获取PPS事件的时间戳和其他相关信息。 PPS_KC_BIND:用于将PPS源绑定到特定的内核消费者。用户空间程序可以通过这个ioctl调用指定PPS源应该向哪个内核消费者发送事件。 3 PPS Souce驱动:pps-gpio PPS-GPIO是Linux内核中用于处理通过GPIO引脚输入的P...
为了解决这个问题,Linux 内核引入了 PPS 机制,通过硬件时钟源来提供高精度的时间戳。其中,PPS 信号通常由 GPS 信号或原子钟等高精度时钟源生成,并通过特定的硬件接口(比如 GPIO)传递给计算机系统。通过使用 PPS 机制,应用程序可以在每秒脉冲到来时获取准确的时间戳,从而实现高精度的时间同步和数据记录。 在Linux 系统...
Raspberry Pi 3上带Buildroot图像的PPSGPIO 、、、 我使用Buildroot试图为Raspberry Pi 3构建一个Linux映像,在该映像中,我可以访问GPIO引脚上的每秒脉冲输入(PPS)。将pps-gpio添加到/etc/modules。然后,我得到一个入口/dev/pps0,当将带有PPS信号的电线连接到RPi3上的物理引脚38并运行pps-test /dev/pps0时,我得...
通过PPS信号,Linux系统可以实现高精度的时间同步,这对于网络通信、科学实验等对时间精度要求较高的应用来说至关重要。 2. 配置Linux系统以接收PPS信号所需的硬件和软件要求 硬件要求: 一个能够产生PPS信号的GPS接收器或其他高精度时钟源。 一个将PPS信号传递给Linux系统的硬件接口,如GPIO(通用输入输出)接口。 软件...
pps-gen { pinctrl-names = "default"; pinctrl-0 = <&pps_gen_pins>; compatible = "pps-gen-gpio"; pps-gen-gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>; default-state = "off"; Please note that in order to use the module with any other board using the device tree infrastructure, the follow...
GPIO - Libgpiod Pin Standardization Since the long famous sysfs GPIO interface (/sys/class/gpio) has been deprecated, the GPIO Char Device API, also known as libgpiod has been adopted by the Linux kernel community as the replacement. The sysfs interface is still supported by Toradex...
gpio- 通用输入/输出(GPIO :General Purpose Input/Output)是可由用户控制行为的芯片的管脚。这里的驱动就是控制GPIO。 gpu- 这些驱动控制VGA、GPU和直接渲染管理(DRM :Direct Rendering Manager )。VGA是640*480的模拟计算机显示器或是简化的分辨率标准。GPU是图形处理器。DRM是一个Unix渲染系统。
This is a patch for pps-gpio module to enable GPIO pin config during module loading.It is based on the PPS patch for Raspberry Pi.The patched pps-gpio module accept three parameters:gpio_pin: the GPIO pin number, default to use pin 18. falling_edge: rising / falling edge of PPS signal...
gpio- 通用输入/输出(GPIO :General Purpose Input/Output)是可由用户控制行为的芯片的管脚。这里的驱动就是控制GPIO。 gpu- 这些驱动控制VGA、GPU和直接渲染管理(DRM :Direct Rendering Manager )。VGA是640*480的模拟计算机显示器或是简化的分辨率标准。GPU是图形处理器。DRM是一个Unix渲染系统。
[ 0.195857] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.201373] sun50i-h6-pinctrl 300b000.pinctrl: initialized sunXi PIO driver [ 0.202133] sun50i-h6-pinctrl 300b000.pinctrl: supply vcc-ph not found, using dummy regulator ...