一、firewall 方式 (centOS7.*) 查看防火墙状态 firewall-cmd --state 如果返回的是 “not running”,那么需要先开启防火墙; 开启防火墙 systemctl start firewalld.service 再次查看防火墙状态,发现已开启! 开启指定端口 firewall-cmd --zone=public --add-port=3306/tcp --permanent 显示success 表示成功 –zo...
selinux was enabledyou need to add the port 587 to http_port_tsemanage port -m -t http_port_t -p tcp 587 # so that haproxy can bind to port 587also need to open port 587 in firewallfirewall-cmd --perm Oracle 开端口 原创 ...
firewall-cmd --zone=public --query-port=1883/tcp 如果是no-表示关闭,yes-表示开启 3.4.开放端口访问 firewall-cmd --zone=public --add-port=1883/tcp --permanent 3.5.重新加载防火墙,这里不是重启防火墙 firewall-cmd --reload 重新执行查看命令,查看端口是否打开即可。 总结 本文从几个方面,分别介绍了...
selinux was enabledyou need to add the port 587 to http_port_tsemanage port -m -t http_port_t -p tcp 587 # so that haproxy can bind to port 587also need to open port 587 in firewallfirewall-cmd --perm Oracle 开端口 原创 chenzudao 2017-05-22 08:44:34 995阅读 linux的打开...
在Linux系统中,open函数用于打开文件或设备文件。如果你遇到使用open函数无法打开串口的问题,可能是由于以下几个原因: 基础概念 串口(Serial Port):是一种串行通信接口,用于设备间的数据传输。 设备文件:在Linux中,硬件设备通常被表示为文件,串口设备通常位于/dev目录下,如/dev/ttyS0或/dev/ttyUSB0。 可能的原因及...
–add-port=8080/tcp #添加端口,格式为:端口/通讯协议 ;add表示添加,remove则对应移除 –permanent #永久生效,没有此参数重启后失效 #进程与状态相关 启动: systemctl start firewalld 关闭: systemctl stop firewalld systemctl status firewalld #查看防火墙状态 ...
其中[port]是要开放的端口号,[protocol]是要使用的协议(如tcp或udp)。此命令将在永久规则中添加一个端口。 3. ufw: ufw是一个简单易用的防火墙配置工具,特别适用于Ubuntu上的开放端口。要允许特定端口通过防火墙,可以使用以下命令: “`shell sudo ufw allow [port] ...
Verify that you are receiving consistent outputs using thesscommand to list listening sockets with an open port: ss-lntu Copy This will print: Output Netid State Recv-Q Send-Q Local Address:Port Peer Address:Port udp UNCONN 0 0 127.0.0.53%lo:53 0.0.0.0:* ...
初始化tty_struct中的uart_state,uart_state中包含uart_port信息,这一步通过步骤1中ops中的open方法来完成。 4.根据步骤3中找到的uart_state,找到里面的uart_port的ops中的startup方法来初始化uart硬件 本文参与 腾讯云自媒体同步曝光计划,分享自作者个人站点/博客。 原始发表:2015-01-15,如有侵权请联系 cloud...
Here are the steps to open a port in CentOS using the command-line interface: Step 1: Check the Current Status of firewalld To check the firewalld services, the “systemctl” command is utilized with the “status” utility as below: ...