1> 首先笔者先是克隆机网络全部是down,然后出现IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 2> 然后关掉克隆机,查看其他宿主机,发现都是同样错误 3> 各种启动网卡,nmcli connection 和netplan apply等均无作用 4> 后来发现是笔者因为前一天打PUBG把很多VM服务关掉,然后重启服务即可。 5> 此时所有...
r8169 0000:05:00.0 eth0: link down IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 二.解决办法 2.1.首先使用的是哪个型号的网卡呢? 在终端输入lspci,笔者输出的网卡相关信息如下: Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller ...
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 二.解决办法 2.1.首先使用的是哪个型号的网卡呢? 在终端输入lspci,笔者输出的网卡相关信息如下: Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller (rev 05) 2.2.那么此网卡使用的是哪个...
linux下有线网卡出现ADDRCONF(NETDEV_UP): eth0: link is not ready的解决方法 2018-05-24 15:02 −... Jello 1 31504 Kibana启动报错 server is not ready yet的解决方案 2019-12-18 15:58 −## 前言: 今天在搭建elasticsearch集群的时候,再次使用Kibana操作elasticsearch的时候报告**Kibana server...
2. No I am not using reference project. I got bit stream from my professor from the university. And then I build the project with patalinux. But I just don't understand that which information should I put in devicetree for ethernet to work and from where should i find it? - all ...
link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready kernel: IP...
I have tried these steps and even downloaded the most current 4.1.15-2 release from the downloads page, but the ethernet is still not working in Linux. Both ethernet ports still report the same link is not ready error, and the link status lights on the ethernet port are not on. I was...
linux下有线网卡出现ADDRCONF(NETDEV_UP): eth0: link is not ready的解决方法 2018-05-24 15:02 −一.背景 2018年5月24日,笔者的pc已经连续运转两天了,突然要使用有线网卡,却发现有线网卡无法正常工作,于是查看了一下内核日志: r8169 0000:05:00.0 eth0: link down IPv6: ADDRCONF(NETDEV_UP): eth...
I use android 4.3 OS, but i think u-boot and kernel might be same as linux as what you attached. I set fec_mac according to the document and what you said. however, the mac address is still not correct after execute "busybox ifconfig". It's really strange symptom.:smileyconfused: ...
This is a bug report This is a feature request I searched existing issues before opening this one Expected behavior After installation and reboot, I expect the docker0 bridge device to have an IP address assigned. Actual behavior No IP a...