Link Aggregation in Manual ModeIn manual mode, you must manually create an Eth-Trunk and add member interfaces to the Eth-Trunk. All active links forward data and traffic is evenly load balanced between them. If one active link fails, traffic is load balanced between the remaining active ...
1. 手工汇聚的配置交换机SWA的配置如下:SWAlink-aggregation group 1 mode manualSWAinteface Ethernet 1/0/1SWA-Ethernet1/0/1port link-aggregation group 1Can not specify a loopback-detect ion en able port asaggregati on group member!系统提示不能将一个启用了端口环回监测功能的端口加入到链路汇聚组 ...
关于切换链路聚合模式,正确的命令表述是A.Link aggregation Mode ManualB.Link-aggregation Mode AutoC.Link-a
Ethernet link aggregation increases link bandwidth by bundling multiple physical links to form a logical link. Link aggregation can work in manual mode or Link Aggregation Control Protocol (LACP) mode. In manual mode, you must manually create an Eth-Trunk and add member interfaces to the Eth-Tru...
具体涉及到的配置命令如下:[H3C]link-aggregationgroupagg-idmode[manual|static][H3C]interfaceinterface-typeinterface-number[H3C-Ethernet1/0/1]portlink-aggregationgroupagg-id首先,创建一个链路汇聚组并指定其类型为手工汇聚还是静态LACP汇聚,然后将相应的端口加入到汇聚组中。需要注意的是,如果要在两台交换机之间...
link-aggregation 1，链路聚合link-aggregation # 创建聚合组号为22 的 手工 | 静态 聚合组，<Sysname> system-view [Sysname] link-aggregation group 22 mode manual | static （manual手工聚合组，static静态LACP聚合组）#创建并配置链路聚合组 1，配置模式为manual，服务类型为tunnel。 <Sysname> system-view [...
1)创建Eth-Trunk #创建Eth-Trunk 1。 <Quidway>system-view Enter system view, return user view with Ctrl+Z. [Quidway]sysname SWA [SWA]interface Eth-Trunk 1 [SWA-Eth-Trunk1]mode manual#聚合方式【manual|lacp-static】 [SWA-Eth-Trunk1]quit 2)向Eth-Trunk中加入成员端口 #将Eth0/0/3加入Eth-...
Aggregate Interface: Route-Aggregation1 Aggregation Mode: Static Loadsharing Type: NonS 表1-5 display link-aggregation verbose命令显示信息描述表 字段 描述 Loadsharing Type 负载分担类型: · Shar:表示负载分担类型 · NonS:表示非负载分担类型 Port Status 端口状态: · Selected:表示处于选中状态 · ...
Figure 6-5Networking for configuring link aggregation in manual mode Configuration Roadmap The configuration roadmap is as follows: Create an Eth-Trunk and add member interfaces to the Eth-Trunk to increase link bandwidth. Create VLANs and add interfaces to the ...
1,链路聚合link-aggregation #创建聚合组号为22的手工|静态聚合组, <Sysname> system-view [Sysname] link-aggregation group 22 modemanual | static (manual手工聚合组,static静态LACP聚合组) #创建并配置链路聚合组1,配置模式为manual,服务类型为tunnel。 <Sysname> system-view [Sysname] link-aggregation group...