license file on the BS. Report Type = Install License Status = Failure Session ID = 65644 Обработка 1,check the license current status used commandDSP LICINFO, the result as below %%DSP LICINFO:;%%RETCODE
打开后的对话框,如图: 首先我们安装的是许可证文件,然后我们再安装主程序。 单击许可证文件即Install License Server 选项,出现安装准备对话框,如图: InstallAnywhere安装准备完成后出现的对话框,选择简体中文,然后点击确定,如图: 点击确定后,进行准备安装 选择下一步进行安装,如图: 这里我们可以更改许可证文件安装的位置...
问题: 尝试启动 Autodesk 2017-2019 版软件时,显示以下许可错误: 许可错误 License Manager 不起作用或未正确安装。<产品名称> 将立即关闭。 注意:如果 2020 版或更高版本 Autodesk 软件出现该问题,请参见 Autodesk 2020 及更高版本中出现“License Manager 不起作用或
License Type: Trial (days restricted) Trial Time Left (days): 180 Current State: In use (IRF模式) 以上显示信息表明,设备上有两个授权可用,其中: · cfa0:/license/2017072009113494375.ak是安装在slot 1上的,用于对数据中心特性的授权,该授权不支持共享。对于不支持共享的授权,其授权信息只显示在安装slot...
你的压缩文件解压过程中可能丢失文件了,或者是你下载的安装文件缺失,重新解压后如果仍然不能够安装的话,建议重新下载。正常情况下,是不存在你报的问题的 那
解决方法如下: 1.首先会进到如下界面: 2.输入1进入许可证信息,再输入2我接受许可协议。图: 3.输入c继续 4.此时会出现license information(license accepted),然后输入c继续,就可以进入系统了。 结论:依次输入1-2-c-c这条文档是否有帮助解决问题? 非常抱歉未能帮助到您。为了给您提供更好的服务,我们很...
那是因为之前的许可证没有卸载干净,你是不是之前装过UG?先卸载干净,把安装目录清理掉,用360把注册表清理一下,重新开机试下
LicenseType:Permanent CurrentState:Inuse 这种情况下通过命令display license看到的状态是In use,但其他信息Feature和Product Description均显示不正常,且dis wlan ap all也看不到license可支持的AP数。解决办法一般是手动把对应的ak文件放置到license目录下,并且重新启动设备就会恢复正常。因此,为了避免这种情况的发生强烈...
I want to use an NI Software product that is licensed through NI Volume License Manager (VLM). Whenever I launch the product, when attempting to connect to the license server I get the following message: Unable to Communicate With License Server. My lo
Catalyst 4500: Cat4k IOS SW licenses are as follows: - for 4503/4506, one enhanced L3 license for the supervisor - for 4507R/4510R, one enhanced L3 license for the chassis Issue 1: Failed: Specified UDI not found You get an error message akin to