const int led = 18; // define the pin void setup() { ledcSetup(channel, freq, resolution); // 设置通道 ledcAttachPin(led, channel); // 将通道与对应的引脚连接 ledcWrite(channel, dutyCycle); // 输出PWM } void loop() { } 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13....
下面的代码来自arduino esp32的wifi例子。 /* WiFiAccessPoint.ino creates a WiFi access point and provides a web server on it. Steps: 1. Connect to the access point "yourAp" 2. Point your web browser to http://192.168.4.1/H to turn the LED on or http://192.168.4.1/L to turn it ...
voidsetup(){//初始化LED引脚为输出模式并熄灭LED灯pinMode(,OUTPUT);digitalWrite(,HIGH);//初始化串口通信Serial.begin(11520);Serial.println();//设置ESP32为STA模式并连接WIFI网络WiFi.mode(WIFI_STA);WiFi.begin(ssid, password);Serial.println();while(WiFi.status() != WL_CONNECTED) {delay(50);Se...
将LED的负极连接到电阻的一端。 将电阻的另一端连接到ESP32的GND引脚上。 确保所有连接都已正确完成。 编写代码 接下来,我们需要编写一段MicroPython代码,让ESP32控制LED灯的亮灭。具体步骤如下: 1.打开Thonny软件。 2.在“文件”菜单中选择“新建”,然后输入以下代码: machine 是大模块,Pin 是 machine 下面的...
pinMode(2,OUTPUT); } void loop() { digitalWrite(2, HIGH); // sets the LED on delay(1000); // waits for a second digitalWrite(2, LOW); // sets the LED off delay(1000); } 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. ...
当输入pin.on()时候,观察 led 会亮起,当输入pin.off()led 会熄灭。 注意: on 和 off 控制的是 GPIO 输出高低,只是凑巧本开发板是共阴极的,因此 on 的时候引脚输出高,正好 led 亮。 对于共阳极的 led,on 是熄灭,off 是亮起。 上面我们是在控制台打印的,想让 esp32 上电就运行程序需要将程序下载到 ...
void led_on(void); void led_off(void); #endif 【编写自定义组件驱动】 components->led->led.c和头文件类似,可根据习惯编写。 #include<stdio.h>#include"led.h"#defineLED_PIN 2voidled_init(void){gpio_config_tled_pin_config; led_pin_config.pin_bit_mask =1<<LED_PIN; ...
led.on() 由此可见如果要链两个led代码就是这样的: importtime frommachineimportPin led=Pin(13,Pin.OUT) led2=Pin(12,Pin.OUT) led.on() led2.on() (pin号码对于链接的io) 网上的图片要加电阻但是我没有,反正我这样接能用 灯珠如果插不上面包板可以把脚弯弯和剪脚 ...
How can you see, after ESP32 go to deep sleep, LED go LOW (in theory). Now, try with hold feature. Code: Select all pinMode(14, OUTPUT); digitalWrite(14, 1); rtc_gpio_hold_en(GPIO_NUM_14); delay(500); esp_deep_sleep(300000000); Now, after deep sleep, LED still HIGH. You...
("esp32_chatter");this->createWallFreq(PUBLISH_FREQUENCY,(ros2::CallbackFunc)publishString,nullptr,publisher_);}};WiFiUDP udp;WiFiServerserver(80);voidsetup(){pinMode(LED,OUTPUT);WiFi.begin(SSID,SSID_PW);while(WiFi.status()!=WL_CONNECTED);server.begin();ros2::init(&udp,AGENT_IP,AGENT...