这段代码是Arduino编程语言的一个经典示例,用于控制一个连接在数字引脚13上的LED灯,使其以每秒闪烁一次的频率持续闪烁。 /* Blink Turns on an LED on for one second, then off for one second, repeatedly. This example code is in the public domain. */ // Pin 13 has an LED connected on most Ar...
setup():setup()函数只运行一次,用来启动Arduino控制器,将运行中不改变的数值和属性固化到芯片中。The setup function runs once when you press reset or power the board. loop() : loop()函数循环执行,直到按下reset键或者移除电源。 2、Blink.ino中用到的几个函数: ① pinMode(pin,mode) : 将指定的引...
打开解压的Arduino IDE文件夹,然后双击Arduino.exe程序。 打开ArduinoBlink.ino草图,请访问: File→Examples → 01.Basics → Blink Blink.ino /*Blink Turns on an LED onforone second,then offforone second,repeatedly.Most Arduinos have an on-board LED you can control.On the UNO,MEGAandZERO itisatt...
Blink*/// 在大多数Arduino控制板上 13号引脚都连接了一个标有“L”的LED灯// 我们给13号引脚设置一个别名“led”int led = 13;//在板子启动或者复位重启后, setup部分的程序只会运行一次void setup(){ // 将“led”引脚设置为输出状态 pinMode(led, OUTPUT);}//setup部分程序运行完后,loop部分的程序...
加载“Blink”例程 你可能会发现你的Arduino板的“L”LED已经在你连接USB插头的时候闪烁了。这是因为Arduino主板通常都是预先安装了“Blink”程序。 在这节课中,我们将用我们自己的Blink程序重新编程Arduino,然后改变它闪烁的速度。 在第0课中,你安装了Arduino IDE,并确保你能找到正确的串口来连接Arduino板。现在是...
下面是Blink程序的代码: /* Blink Turns an LED on for one second, then off for one second, repeatedly. Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO it is attached to digital pin 13, on MKR1000 on pin 6. LED_BUILTIN is set to the correct LED pi...
为什么arduino的blink中pinmode是LED_BUILTIN而不是13号引脚。是因为LED_BUILTIN函数主要用来点亮Arduino主板内置的LED灯的,Arduino有不同的板型,主板内置的LED灯的引脚也有所不同,不一定都是13引脚。用LED_BUILTIN函数不管主板内置的LED灯是哪个引脚都回被点燃亮。看...
/*Blink Turns on an LED on for one second, then off for one second, repeatedly. This example code is in the public domain.*///Pin 13 has an LED connected on most Arduino boards.//give it a name:intled =5; #这里将原来的13改为5,当然你也可以改为其实端口,只要和led正极连接端口相一...
/*Blink Turns on an LED on for one second, then off for one second, repeatedly. This example code is in the public domain.*///Pin 13 has an LED connected on most Arduino boards.//give it a name:intled =5; #这里将原来的13改为5,当然你也可以改为其实端口,只要和led正极连接端口相一...
代码编译完没问题后,点击图中所选按钮将其上传至 Arduino UNO 板上。 手机设置 点击CONNECT,选择蓝牙,点击连接。 点击中间的麦克风,进行语音输入 实际结果 语音输入 turn on the yellow:黄色的灯会打开 语音输入 turn on the red:红色的灯会打开 语音输入 blink:两个灯会一起闪烁 语音输入 stop:两个灯会停止闪...