将I2C 扫描仪代码上传到 Arduino Uno。 第2步 如果您有 I2C LCD,请跳过此步骤。但如果您有 16x2 LCD 和 I2C 模块,请参阅将此模块连接到 LCD 的步骤。 联系 首先焊接 I2C 模块。I2C 模块上没有用于连接 16x2 LCD 的标签。所以在下面给出的图像的帮助下焊接它 16x2 LCD 上的 I2C 模块 焊接后将 I2C ...
我们可能需要得到匿名登录的uid const app = tcb.init({ env: '替换云开发环境id' })...
#include<LiquidCrystal_I2C.h>LiquidCrystal_I2Clcd(0x3F,16,2);// set the LCD address to 0x3F for a 16 chars and 2 line displayvoidsetup(){lcd.init();lcd.clear();lcd.backlight();// Make sure backlight is on// Print a message on both lines of the LCD.lcd.setCursor(2,0)...
如图1所示启动Visuino 单击Visuino中Arduino组件(图1)上的“工具”按钮 出现对话框时,选择“Arduino UNO”,如图2所示 第4 步:在 Visuino 添加组件 1 / 5 添加2X“检测边缘”组件 添加“加/减计数器”组件 添加“时钟多源”组件 添加5X“文本值”组件 添加“液晶显示器 (LCD) - I2C”组件 第5 步:在 Visuin...
Arduino中使用I2C通信可直接调用Wire.h库, 这个库允许Arduino链接其他I2C设备, 链接线有两条, 分别是SDA(数据行)和SCI(时钟线). 各型号Arduino的I2C对应引脚: Arduino Board:I2C / TWI pins Arduino Uno/Ethernet:A4 (SDA), A5 (SCL) Arduino Mega2560:20 (SDA), 21 (SCL) ...
Arduino中使用I2C通信可直接调用Wire.h库, 这个库允许Arduino链接其他I2C设备, 链接线有两条, 分别是SDA(数据行)和SCI(时钟线). 各型号Arduino的I2C对应引脚: Arduino Board:I2C / TWI pins Arduino Uno/Ethernet:A4 (SDA), A5 (SCL) Arduino Mega2560:20 (SDA), 21 (SCL) ...
Gravity: I2C 16x2 Arduino LCD with RGB Backlight Display V2.0 $11.90 Gravity: I2C 16x2 Arduino LCD with RGB Font Display (Black) V2.0 $11.90 Gravity: I2C LCD1602 Arduino LCD Display Module (Blue) $9.90 Gravity: I2C LCD1602 Arduino LCD Display Module (Green) $9.90 Gravity: I2C LCD1602 ...
I2C 2×16 LCD 範例說明 介紹 一般LCD有許多pin腳, 以手上這片LCD為例有16個pin 直接控制LCD的話會用掉許多pin, 在資料處理上也很麻煩, 所以一般LCD會有額外的控制晶片幫忙處理, 並且使用I2C介面控制這塊控制晶片。 流程 打開範例, “File” -> “Examples” -> “AmebaWire” -> “LCD_HelloWorld”, 編...
Arduino-compatible I2C/UART LCD shield with 16x2 display with backlight and 4 buttons, Arduino library and demo examples. Accepts commands by I2C(default) or UART.FEATURES 2-row display with 16 character on each row Backlight 4 tactile buttons PIC16F722A microcontroller with built-in custom fi...
1x Arduino UNO 1x LCD 16x2 1x PCF8574T转接板 电烙铁、焊锡、松香等 接线 首先,把转接板焊接到LCD显示屏上(方向如上图) SCL -> 最上面的口 SDA -> 第二个口 扫描I2C地址 将以下代码拷贝到Arduino IDE,并执行。然后选择工具->串口监视器,把右下角的波特率改为115200,即可读出I2C地址,如下图。