lacp mixed-rate link enable 当Eth-Trunk接口中存在不同速率的成员接口时,活动接口的选择仍是按照主动端设备的接口优先级、端口ID,选择活动接口。如果希望指定端口成为活动端口,可以配置成员接口的LACP优先级提高接口优先级。 配置Eth-Trunk接口中活动接口数上限阈值 ...
lacp mixed-rate link enable 当Eth-Trunk接口中存在不同速率的成员接口时,活动接口的选择仍是按照主动端设备的接口优先级、端口ID,选择活动接口。如果希望指定端口成为活动端口,可以配置成员接口的LACP优先级提高接口优先级。 配置Eth-Trunk接口中活动接口数上限阈值 lacp max active-linknumber link-number 为保证...
bond6:通过修改ARP包实现负载均衡, 即对到来的arp请求依据一定策略使用不通过的arp进行回复 2.2 示例:将eth1和eth2两张网卡使用mode 4 也就是LACP模式进行绑定 auto bond0 iface bond0 inet manual bond-slaves eth2 eth1 bond-miimon 100 bond-mode 4 bond-lacp-rate 1 bond-xmit-hash-policy 2 mtu 9000...
示例如下: auto bond0 iface bond0 inet static address 192.168.1.10 netmask 255.255.255.0 gateway 192.168.1.1 bond-mode 4 bond-miimon 100 bond-lacp-rate 1 bond-slaves etho eth1 复制代码 在上述配置中,eth0 和eth1 是需要绑定的物理网卡名称,bond-mode 4 表示启用LACP模式。 重启网络服务 保存并关闭...
其中,bond-mode 4表示使用LACP模式,bond-miimon 100设置监测间隔为100毫秒,bond-lacp-rate 1设置LACP控制帧发送速率为1。 重启网络服务 保存并关闭文件后,重启网络服务以应用配置更改: sudoservice networking restart 验证配置 验证LACP配置是否正常工作。可以使用以下命令检查Bond接口的状态: ...
其中,bond-mode 4表示使用LACP模式,bond-miimon 100设置监测间隔为100毫秒,bond-lacp-rate 1设置LACP报文发送的速率为1。 重启网络服务:保存并关闭文件后,重启网络服务以应用配置更改。使用命令sudo service networking restart来重启网络服务。 验证配置:验证LACP配置是否正常工作。可以使用命令cat /proc/net/bonding/bo...
lacp mixed-rate link enable 当Eth-Trunk接口中存在不同速率的成员接口时,活动接口的选择仍是按照主动端设备的接口优先级、端口ID,选择活动接口。如果希望指定端口成为活动端口,可以配置成员接口的LACP优先级提高接口优先级。 配置Eth-Trunk接口中活动接口数上限阈值 lacp max active-linknumber link-number 为保证...
bond-lacp-rate 1 bond-slaves eth0 eth1 在上述配置中,将eth0和eth1两个网络适配器绑定到bond0接口上,并使用LACP模式(bond-mode 4),设置监测间隔(bond-miimon 100),设置LACP控制帧发送速率(bond-lacp-rate 1)。 重启网络服务:保存并关闭文件后,重启网络服务以应用配置更改。使用以下命令重启网络服务: ...
BONDING_OPTS="mode=4 miimon=100 lacp_rate=1" 配置第一个子接口 修改你希望添加到绑定中的第一个子接口。请根据你的实际环境使用合适的接口名。 vi /etc/sysconfig/network-scripts/ifcfg-ens192 TYPE=Ethernet BOOTPROTO=none DEVICE=ens192 ONBOOT=yes ...
lacp-rateslow Parameters fast Uses the fast LACP rate, which is every 1 second. This setting is the default value. slow Uses the slow LACP rate, which is every 30 seconds. Guidelines Thelacp-ratecommand sets the rate in the Link Aggregation Control Protocol (LACP) aggregation. ...