Router(config-if)#lacp max-bundle 2 Router(config-if)#ip address 10.1.1.1 255.255.255.0 Router(config)#interface g2/0/0 Router(config-if)#no ip address Router(config-if)#lacp port-priority 100 Router(config-if)#channel-group 1 mode passive ...
- lacp max-bundle:链路聚合组的最大带宽,单位为兆比特每秒(Mbps); - lacp timeout:lacp探测周期,单位为秒; - lacp rate:lacp控制报文发送频率,包括慢速模式(slow)、快速模式(fast)和长模式(long)。 5. 注意事项 在使用lacp封装命令进行链路聚合配置时,需要注意以下几点: - 链路聚合组中至少需要有两个成员接...
2)指定最大活动链路数,在集聚接口配置模式下,使用以下命令:lacp max-bundle number# number–指定最大活动链路数。取值范围为 1 到 16,默认值为 16。 3)使用该命令 no 的形式恢复最大活动链路数的默认值:no lacp max-bundle。 指定最小活动链路数 ...
lacp max-bundle max-bundles Router(config-if)# lacp max-bundle 4 PoA に接続する max-bundle リンクを設定します。max-bundles 引数の値は、PoA に接続している LAG 内のリンクの総数よりも小さくする必要があります。 • 冗長グループが、DHD コントロール、PoA コントロール、またはこ...
配置BFD Link-bundle会话必须指定源IPv4地址,该地址为本端三层Eth-Trunk接口的地址。 9.4 配置步骤 (1) 配置H3C Device A设备 # 创建三层聚合接口1,配置该接口为动态聚合模式,并为其配置IP地址和子网掩码。 <DeviceA> system-view [DeviceA] interface route-aggregation 1 [Device...
如果当前的聚合组数大于所配置的max-group-number,则本命令配置失败。 配置link-aggregation capability命令后如果继续创建聚合组,且聚合组数超过了本命令配置的max-group-number,则会导致设备重启后部分聚合组配置丢失。 聚合组中的最大选中端口数为本命令及link-aggregation selected-port maximum命令配置值中的较小值。
基于LACP技术的某企业业务负载方案.docx,PAGE 37 题目 基于LACP技术的某企业业务负载方案 摘要 LACP协议是IEEE802.3ad标准的主要内容,其中的链路聚合(link aggregation)是一种实现动态聚合的技术。所以当LACP(Link Aggregation Control Protocol)技术的出现,有效的提
Depending on the platform and for LACP EtherChannel in case of 3850’s, you can bundle up to 16 interfaces of the same type in the EtherChannel but only up to eight ports can be active at one time. Here’s how to do it with the example from above: ...
bundle.h byte-order.h byteq.c byteq.h ccmap.c ccmap.h cfm.c cfm.h classifier-private.h classifier.c classifier.h cmap.c cmap.h colors.c colors.h colors.man command-line.c command-line.h common-syn.man common.man common.xml compiler.h connectivity.c connectivity.h conntrack-icmp.c ...
Solved: I have configured an 4 interface etherchannel with a NetApp storage device. This is the second bundle to the second controller of the NetApp device, the other one works fine with the same config. I am getting all the interfaces with a status