KlipperDelta配置文件,针脚适配于MKS BASE1.4主板 虚拟SD卡文件,GCODE文件路径适用于Mainsail控制面板 连杆长度,限位开关位置,打印范围之类的需要自己用塞纸法自动校准一下 [mcu]serial:/dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL00PU19-if00-port0# 连接到单片机的串行通讯接口# 如果你不确定的话(或可能...
Fluidd设置 为Fluidd提供一些控制端口,virtual_sdcard的path可以设置Gcode存放的位置 printer 设置打印机的基本参数 步进电机配置 这里根据实际的情况进行配置 [stepper_x] 标志这是x轴步进电机的配置项 [tmc2208 stepper_x] 标志这是x轴步进电机驱动器的配置项。驱动器的型号为tmc2208 其他轴的配置类似,根据实际情况...
[virtual_sdcard]path:~/printer_data/gcodes[gcode_macroCANCEL_PRINT]rename_existing:CANCEL_PRINT_BASEgcode:# 以下为可选配置[respond] [force_move]enable_force_move:True[temperature_sensorhost]sensor_type=temperature_host 连接后如图所示: 2.2 配置摄像头串流# 我们要正确设置摄像头以获取图像 Copy ## c...
# This file contains common pin mappings for Ultimaker UltiMainboard v2 # boards. To use this config, thefirmwareshould be compiled for the # AVR atmega2560. # See docs/Config_Reference.md for a description of parameters. [include fluidd.cfg] [virtual_sdcard] # path: /home/henrik/printer_...
[virtual_sdcard]path:~/gcode_files[gcode_macroCANCEL_PRINT]description:无实际作用,避免出现黄字报错rename_existing:CANCEL_PRINT_BASEgcode:### 用于调试[respond] 3、输出效应器:创建不同 DC 风扇配置# 直流风扇主要有三种: 两线风扇:VCC + GND,可以实现开和关两种状态...
6、把printer.cfg的[virtual_sdcard], [display_status], [pause_resume]删掉,另有文件集成了。在printer.cfg开头加上两个头文件[include client.cfg] [include client_macros.cfg]即可。还有其他的宏都添加到client_macros.cfg文件里。 7、klipper连不上。先检查硬件线路有无问题,如果都正常,通常是mcu serial没...
###[virtual_sdcard] path: ~/printer_data/gcodes [display_status] [pause_resume] [gcode_macro CANCEL_PRINT] description: Cancel the actual runningprintrename_existing: CANCEL_PRINT_BASE gcode: TURN_OFF_HEATERS CANCEL_PRINT_BASE### # 主板温度显示 ###...
[virtual_sdcard] path: ~/printer_data/gcodes on_error_gcode: CANCEL_PRINT [pause_resume] #recover_velocity: 50. # When capture/restore is enabled, the speed at which to return to # the captured position (in mm/s). Default is 50.0 mm/s. [display_status] [respond] [gcode_macro CANCE...
filename, total_duration, print_duration, filament_used, state, message: Estimated information about the current print when a virtual_sdcard print is active. info.total_layer: The total layer value of the last SET_PRINT_STATS_INFO TOTAL_LAYER=<value> G-Code command. info.current_laye...
'toolhead', 'virtual_sdcard', 'webhooks', 'motion_report', 'firmware_retraction', 'exclude_object', 'manual_probe', ] klipperscreendir = pathlib.Path(__file__).parent.resolve() def set_text_direction(lang=None): rtl_languages = ['he'] if lang is None: ...