所以我们用 path 来进行区分,此处类似 klipper 的 serial 地址查找方法:ls /dev/v4l/by-path/*#地址分别对应不同的USB接口,选择 index0 地址修改所有 webcam*.txt,
按一下主板上的reset按钮 输入代码ls /dev/serial/by-id/查询主板的串口ID来确认固件是否烧录成功,如果烧录成功了会返回一个Klipper的设备ID,类似这样的代码/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0,如下图 将得到的这串代码复制下来,接下来Klipper配置里面会用到 如果失败了,检查上述步骤是不是...
#设置串口波特率 250000python3 ./mysetbaud.py <> /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0 250000#重启下位机进入 Katapultecho $'~ \x1c Request Serial Bootloader!! ~' >> /dev/serial/by-id/usb-Klipper_stm32f407xx_mks-monster8-if00 4.3...
选择好nano的cpu mega328,com口和hex文件,之后点击upload等他上传成功就行了。 3.配置cfg文件 在配置里面写入 [mcunano] # cmu的名字,下面是mcu的地址 serial: /dev/serial/by-id/usb-1a86_USB2.0-Ser_-if00-port0 [adxl345] # adxl345的引脚定义,可以按照下面的定义接线 cs_pin: nano:PB2 spi_softwa...
make flash FLASH_DEVICE=/dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AM00P0TD-if00-port0 sudo service klipper start 这里就已经给f5主板刷入klipper了。接下来就是配置的部分 先打开klipper的github,找到config文件夹 https://github.com/KevinOConnor/klipper/tree/master/config ...
The Pico will now reboot with the new firmware and should show up as a serial device. Find the pico serial device with ls /dev/serial/by-id/*. You can now add an adxl.cfg file with the following settings: [mcu adxl] # Change <mySerial> to whatever you found above. For ...
vendor id: 2341 usb device id: 0xabcd usb serial number: 12345 make got this error now (this is new) ERROR: The compiler failed to correctly compile Klipper It will be necessary to upgrade the compiler See: https://bugs.launchpad.net/ubuntu/+source/newlib/+bug/1767223 apt update apt...
serial: /dev/serial/by-id/usb-Klipper_sam4e8e_00313753383436313230303637303433-if00 [sx1509 duex] i2c_address: 62 # Address is fixed on duex boards [static_digital_output onboard_led] pins: !PC2 [output_pin GPIO1] # General purpose pin broken out on the duex ...
OR use the provided image I built located inside Firmware/OpenWrt_snapshot - Be aware though that this was built with only the kmod-usb-serial-ch431 - if your mainboard is different -> use the above instructions to compile. 2. Install OpenWrt to the device Click to expand! Flashing: ...
lxc容器较vm更轻量更快 ...虽然也没什么用 宿主机 /etc/pve/lxc/{id}.conf 添加以下内容, 把usb的路径分配到容器 lxc.mount.entry: /dev/serial/by-id/usb-Klipper_stm32f407xx_470050000650315657353120-if00 dev/serial/by-id/usb-Klipper_stm32f407xx_470050000650315657353120-if120-if00 none bind,...