输入PID_CALIBRATE heater=extruder target=220，待喷头温度曲线波动5次之后，输入SAVE_CONFIG保存配置；4、热床pid矫正 输入PID_CALIBRATE heater=heater_bed target=60，待热床温度曲线波动5次之后，输入SAVE_CONFIG保存配置；至此，所有安装调试工作全部完成，最后用户完成打印机调平，则可通过klipper控制端控制打印机进...
输入PID_CALIBRATE heater=extruder target=220,待喷头温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 4、热床pid矫正 输入PID_CALIBRATE heater=heater_bed target=60,待热床温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 至此,所有安装调试工作全部完成,最后用户完成打印机调平,则可通过klipper控制端控制打印机进行高...
# 校准热端PIDPID_CALIBRATEHEATER=extruderTARGET=170 # 校准热床PIDPID_CALIBRATEHEATER=heater_bedTARGET=60 在打印机冷却到室温后,我们依次将命令粘贴到命令行内: 然后点击发送,这时候打印机会自动将热端加热至170度,并持续一段时间反复测试: 我们耐心的等待程序自动结束,然后我们点击蓝色SAVE_CONFIG按钮,Fluidd会...
输入PID_CALIBRATE heater=extruder target=220,待喷头温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 4、热床pid矫正 输入PID_CALIBRATE heater=heater_bed target=60,待热床温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 至此,所有安装调试工作全部完成,最后用户完成打印机调平,则可通过klipper控制端控制打印机进行高...
输入PID_CALIBRATE heater=extruder target=220,待喷头温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 4、热床pid矫正 输入PID_CALIBRATE heater=heater_bed target=60,待热床温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 至此,所有安装调试工作全部完成,最后用户完成打印机调平,则可通过klipper控制端控制打印机进行高...
输入PID_CALIBRATE heater=extruder target=220,待喷头温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 4、热床pid矫正 输入PID_CALIBRATE heater=heater_bed target=60,待热床温度曲线波动5次之后,输入SAVE_CONFIG保存配置; 至此,所有安装调试工作全部完成,最后用户完成打印机调平,则可通过klipper控制端控制打印机进行高...
[extruder] step_pin: PL7 dir_pin: PL6 enable_pin: !PC0 microsteps: 16 # 382.165 full_steps_per_rotation: 200 gear_ratio: 50:17 rotation_distance: 23.132 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PE4sensor_type: PT100 INA826 ...
pid_kp =26.213pid_ki =1.304pid_kd =131.721pressure_advance:0.05pressure_advance_smooth_time:0.040 [tmc2208 extruder] uart_pin: PA15#microsteps: 16interpolate: True run_current:0.6hold_current:0.4sense_resistor:0.110stealthchop_threshold:200###Z0轴设置###[stepper_z]#Z0电机脉冲引脚设置s...
pi@octopi:~/klipper $ git rev-parse HEAD 62fc5dc2884c41eb45880b0e9c988cabb025d1c1 Running on a Pi3 with a genuine E3D V6 heater and thermister. I run PID_CALIBRATE HEATER=extruder TARGET=220, then the temperature graph will look like I'v...
Klipper is a 3d-printer firmware. Contribute to Klipper3d/klipper development by creating an account on GitHub.