此配置文件,UP主没有验证过。配置时请谨慎进行。 # This file contains common pin mappings for the 2018 Creality # Ender 3. To use this config, the firmware should be compiled for the # AVR atmega1284p. # Note, a number of Melzi boards are shipped with a bootloader that # requires the fol...
3.修改Klipper配置文件 Klipper的github库的CONFIG目录下有该打印机的配置文件，先下载下来作为模板，部分参数还需要修改；将下载下来的文件改名为printer.cfg，替换~/printer_data/config下的同名文件；将泰山派与打印机连接，Ender3 S1 ProUSB转串口芯片采用CH340，可以通过lsusb指令查询得知；查询设备的串口号输入ls /...
我的ender3v2升级了黑骑士的线轨套装,Y轴最大行程减少了20mm # This file contains pin mappings for the stock 2020 Creality Ender 3 # V2. To use this config, during "make menuconfig" select the # STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) # communication. #用...
Klipper的github库的CONFIG目录下有该打印机的配置文件,先下载下来作为模板,部分参数还需要修改; 将下载下来的文件改名为printer.cfg,替换~/printer_data/config下的同名文件; 将泰山派与打印机连接,Ender3 S1 ProUSB转串口芯片采用CH340,可以通过lsusb指令查询得知; 查询设备的串口号输入ls /dev/ttyUSB*查询; 不建...
3.修改Klipper配置文件 Klipper的github库的CONFIG目录下有该打印机的配置文件,先下载下来作为模板,部分参数还需要修改; 将下载下来的文件改名为printer.cfg,替换~/printer_data/config下的同名文件; 将泰山派与打印机连接,Ender3 S1 ProUSB转串口芯片采用CH340,可以通过lsusb指令查询得知; ...
下载Klipper的github库中的CONFIG目录下的模板文件，并将其重命名为printer.cfg，替换为~/printer_data/config下的文件。使用网页打开printer.cfg进行修改。根据实际情况调整[mcu]下的内容，添加RK3566和STM32的温度显示。对于Ender3 S1 Pro的串口号，建议使用绑定ID的方式，以避免接入多个CH340时Klipper上位...
Hi, The log is attached below. I am at the early stages of running Klipper on Duet3d/Ender3 ( still haven't done all the work on the config.cfg). I run into a deadlock. There is a need to do "FIRMWARE RESTART" , but i can not do it as th...
README.md config.lock modified - 14/11/24 - 00:24:13 Nov 14, 2024 Repository files navigation README Klipper-Backup 💾 Klipper backup script for manual or automated GitHub backups This backup is provided by Klipper-Backup.About Ender 3 with Klipper and some mods Resources Readme Activi...
创想三维Ender2Pro Klipper固件地址:【传送门】 点击下载 下载完.bin文件后,在打印机的SD卡中创建Factory文件夹后将刚下载完.bin文件放入,后关闭打印机,将SD卡重新插入打印机,此时由于还未接入上位机,所以打印机界面蓝屏为正常。 若需要刷回原来的固件只需要进入创想三维官网找到对应固件进行烧录即可【传送门】 ...
REPRAP (DUET), and Klipper firmware, making it a go-to choice for both Ender 3 and Ender 3 Pro users. **Advanced Features and User-Friendly Interface** The Mellow 32bit FLY-CDY V3 Wifi Control Board is not just about performance; it's also about user-friendly features that make your...