1、Z轴离床间隙 PROBE_CALIBRATE A4纸测试抽拉有些微阻力 2、 Probe的精度检测,应当小于0.003 PROBE_ACCURACY 3、自动震动补偿测量 SHAPER_CALIBRATE 4、自动(手动)床网补偿 BED_MESH_CALIBRATE [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 10, 10 #起始点位 mesh_max: 110, 110 #结束点位 pr...
self.helper._move_safe_z(pos, self.helper.lift_speed) # move to position if split_xy: self.helper._move([site[0], pos[1], None], self.helper.speed) @@ -399,18 +431,28 @@ def calibrate_z(self): " new offset=%.6f"
def cmd_CALIBRATE_Z(self, gcmd): self.last_state = False if self.z_homing is None: raise gcmd.error("%s: must home axes first" % (gcmd.get_command())) nozzle_site = self._get_nozzle_site(gcmd) switch_site = self._get_switch_site(gcmd, nozzle_site) bed_site = self....
#PID_CALIBRATE HEATER=extruder TARGET=170 pid_kp = 14.488#先将模型冷却风扇设置为25%的转速( M106 S64 ),然后发送命令PID_CALIBRATE HEATER=extruder TARGET=245 它将执行一个PID校准程序,将持续约5分钟,完成后控制台将返回PID数值,将其复制到配置文件即可。 pid_ki = 3.715 pid_kd = 14.125 pressure_adva...
G1 Z1 waiting the toolhead stops then M102 S-2 Check if the zero position is as expected byG1 Z0afterG28, if not please calibrate again. Gcode Command for BDsensor: BDSENSOR_VERSION # equals M102 S-1 , read the version of BDsensor ...
if 'manual_probe' in data and data['manual_probe']['is_active'] and 'zcalibrate' not in self._cur_panels: self.show_panel("zcalibrate", _('Z Calibrate')) elif action == "notify_filelist_changed": if self.files is not None: self.files.process_update(data) ...
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be ...
GUI for Klipper. Contribute to KlipperScreen/KlipperScreen development by creating an account on GitHub.
默认是250000#canbus_uuid:# 如果使用一个连接到CAN总线的设备,这个参数需要被设置为# 要连接的芯片的唯一ID。# 当使用CAN总线时,这个参数必须给定#canbus_interface:# 当使用的设备连接到CAN总线时,这个参数需要被设置为# 使用的网络接口# 默认值是can0restart_method:arduino# 这个参数控制着重置单片机的方式#...
Delta_Calibrate.md Endstop_Phase.md Example_Configs.md Exclude_Object.md FAQ.md Features.md G-Codes.md Hall_Filament_Width_Sensor.md Installation.md Kinematics.md MCU_Commands.md Manual_Level.md Measuring_Resonances.md Multi_MCU_Homing.md Overview.md Packaging.md Pressure_Advance.md Prob...