Calibrate first layer with paper trick, this time changing extruder 1 Z offset to adjust height. (Move back and forward - I don't think it moves if you just change it.)Calibrate e-steps - T0 and T1https://docs.vorondesign.com/build/startup/#extruder-calibration-e-stepsFirst layer T0 ...
microsteps: 16 rotation_distance: 8 endstop_pin: ^!PA7 #position_endstop: 304 position_max: 302 homing_speed: 10.0 position_min: -1.0 [extruder] step_pin: PL7 dir_pin: PL6 enable_pin: !PC0 microsteps: 16 # 382.165 full_steps_per_rotation: 200 gear_ratio: 50:17 rotation_distance:...
这里使用的是富源盛蜘蛛v1.1的主板,他的相关配置和烧录过程可以参考文档:https://github.com/FYSETC/FYSETC-SPIDER/blob/main/%E8%AF%B4%E6%98%8E%E6%96%87%E6%A1%A3_%E4%B8%AD%E6%96%87.md 其他型号的主板可以找对应的厂商寻找,或根据实际的情况自行设置。 先使能 extra low-level configuration option...
PE9#---Klipper0.9以上版本设置---# 电机细分设置microsteps:16# 主动带轮周长mm(2GT-20T带轮40,2GT-16T带轮32)rotation_distance:40# 电机单圈所需脉冲数(1.8度电机:200,0.9度电机:400)full_steps_per_rotation:200# X轴最小行程--软件限位position_min:0# X轴最大行程--软件限位(如果是350机型,需...
pid_kp = 14.488#先将模型冷却风扇设置为25%的转速( M106 S64 ),然后发送命令PID_CALIBRATE HEATER=extruder TARGET=245 它将执行一个PID校准程序,将持续约5分钟,完成后控制台将返回PID数值,将其复制到配置文件即可。 pid_ki = 3.715 pid_kd = 14.125 ...
Steps To Reproduce Steps to reproduce the behavior: after adding this snippet to configuration.nix and sudo nixos-rebuild switch, the rebuild fail. services.klipper = { configFile = "/home/nicolas/printer_conf/printer.cfg"; enable = true...
microsteps:16 full_steps_per_rotation: 200 #gear_ratio: #step_pulse_duration: endstop_pin:PD2 #position_min: -2 #position_endstop:0 #position_max:159.07 homing_speed: 150 homing_retract_dist: 15 homing_retract_speed:80 [delta_calibrate] ...
## Fine tune E steps [extruder] section [mcu] ## Uncomment below if you're using the Raspberry uart0 to communicate with Spider #restart_method: command ## You need to select 'Communication interface' to USB in 'make menuconfig' ## when you compile Klipper for Spider ## Obtain...
## Fine tune E steps [extruder] section [mcu] ## Uncomment below if you're using the Raspberry uart0 to communicate with Spider #restart_method: command ## You need to select 'Communication interface' to USB in 'make menuconfig' ## when you compile Klipper for Spider ## Obtain...
uart_pin: PA15#microsteps: 16interpolate: True run_current:0.6hold_current:0.4sense_resistor:0.110stealthchop_threshold:200###Z0轴设置###[stepper_z]#Z0电机脉冲引脚设置step_pin: PE2#Z0电机方向引脚设置,可以通过添或删除引脚前面的!来改变电机的运转方向dir_pin: !PE4#Z0电机使能引脚设置enable_...