BED_MESH_CALIBRATE PROFILE=<name> METHOD=[automatic] [<probe_parameter>=<value>] [<mesh_parameter>=<value>] Probe_parameter和mesh_parameter为上述需要设置的值。使用MESH_MIN, MESH_MAX和PROBE_COUNT来定义它们。这里有一个例子: BED_MESH_CALIBRATE PROFILE=mesh1 METHOD=automatic MESH_MIN=5,5 MESH_...
mesh_radius:自动调平的半径。 probe_count:探针的数量。 fade_start、fade_end和fade_target:自动调平时的渐变效果。 在OctoPrint中选择“Control”选项卡,点击“Connect”连接到3D打印机。接下来,在命令行中输入BED_MESH_CALIBRATE,3D打印机就会开始自动调平。 三、注意事项 在进行Klipper自动调平配置之前,需要注意...
1、Z轴离床间隙 PROBE_CALIBRATE A4纸测试抽拉有些微阻力 2、 Probe的精度检测,应当小于0.003 PROBE_ACCURACY 3、自动震动补偿测量 SHAPER_CALIBRATE 4、自动(手动)床网补偿 BED_MESH_CALIBRATE [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 10, 10 #起始点位 mesh_max: 110, 110 #结束点位 pr...
(因为bltouch位置距离挤出头有一个偏移,所以可做网床的大小要比实际热床小,一般mesh_min就是热床起始位置加上一个偏移值(10左右),mesh_max是热床最大位置减去bltouch的offset值再减一个附加偏移值); probe_count: 为x和y各取几个点。 设置完成后,保存重启。 先复位,然后输入 BED_MESH_CALIBRATE,可以看到bl...
//raw.githubusercontent.com/jlas1/Klicky-Probe/main/Klipper_macros/Klipper_macros.zip# 解压unzip Klipper_macros.zip# 解压以后新增的文件klicky-probe.cfg#选择要开启功能的配置文件klicky-variables.cfg#存储Klicky使用的变量klicky-bed-mesh-calibrate.cfg#网床调平脚本klicky-quad-gantry-level.cfg#4Z调平...
probing, a mesh is generated and z-movement is adjusted according to the mesh. `BED_MESH_CALIBRATE [PROFILE=<name>] [METHOD=manual] [HORIZONTAL_MOVE_Z=<value>] [<probe_parameter>=<value>] [<mesh_parameter>=<value>] [ADAPTIVE=1] [ADAPTIVE_MARGIN=<value>]`: This command probes the b...
KevinOConnormerged commita77d079intoKlipper3d:masterFeb 20, 2024 1 check passed Collaborator pedrolamasdeleted thepedrolamas/docs-bed-mesh-calibratebranchFebruary 20, 2024 17:26 Reviewers voidtrancevoidtrance approved these changes 3 participants
[bed_mesh]## 热床网格校准speed:60# 校准速度horizontal_move_z:13# Z起始高度mesh_min:50,50# 最小校准点坐标x,ymesh_max:250,250# 最大坐标probe_count:15,15# 采样点数mesh_pps:2,2# 补充采样点数algorithm: bicubic# 算法模型bicubic_tension:0.2# 算法插值不要动relative_reference_index:112# 第...
Klipper: Bed Mesh – Simply Explained First layers can be hard to get right. Thankfully, Klipper can help. Learn how to use Klipper for bed mesh compensation. The Newest Wares Klipper vs Marlin: The Main Differences When choosing 3D printer firmware, you might be looking at Klipper vs. Mar...
BED_MESH_PROFILE LOAD=default 完整配置如下 printer.cfg # This file contains common pin mappings for Ultimaker UltiMainboard v2 # boards. To use this config, thefirmwareshould be compiled for the # AVR atmega2560. # See docs/Config_Reference.md for a description of parameters. ...