Copy # [include override.cfg][idle_timeout]timeout:600[printer]max_accel:15000max_accel_to_decel:7500max_z_velocity:7.5max_z_accel:150square_corner_max_velocity:100.0[stepper_x]position_endstop:228homing_speed:40[tmc2209stepper_x]stealthchop_threshold:999999# hold_current:1.0driver_SGTHRS:83[...
层高0.2,填充和顶层都设置为0,打印速度设置为100,动态加速控制关闭,注意切片的时候不要旋转模型,保持原始面向。 然后我们把打印机参数调整到这里给出的设置,max_accel和max_accel_to_decel设置为7000,SQUARE_corner_velocity设置为5,这些设置都是为了放大共振,方便我们测量。 然后重启klipper 在打印之前还要在console中...
max_accel:4500 # Maximum acceleration (in mm/s^2) of the toolhead (relative to the # print). This parameter must be specified. #max_accel_to_decel: # A pseudo acceleration (in mm/s^2) controlling how fast the # toolhead may go from acceleration to deceleration. It is used to # ...
toolhead: Replace max_accel_to_decel with minimum_cruise_ratio Browse files The user facing max_accel_to_decel setting is complicated and confusing. Replace it with a new minimum_cruise_ratio parameter. Internally this user-facing parameter will calculate the existing low-level "accel_to_decel...
For calls that set the ACCEL parameter, the ACCEL_TO_DECEL parameter is also set and scaled by variable_velocity_decel_scale (default: 0.5). The M900 command is implemented by calling Klipper's SET_PRESSURE_ADVANCE command. The K factor is scaled by variable_pressure_advance_scale (default:...
max_accel_to_decel: 500 max_z_velocity: 6 max_z_accel: 120 square_corner_velocity: 10.0 [pause_resume] recover_velocity: 150 [input_shaper] shaper_freq_x: 98.6 # per accelerometer shaper_type_x: 2hump_ei shaper_freq_y: 73.6 # per accelerometer ...
"max_accel", "max_accel_to_decel", "max_velocity", "square_corner_velocity"], "virtual_sdcard": ["file_position", "is_active", "progress"], "webhooks": ["state", "state_message"], "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unret...
max_accel_to_decel:3000#最大加速度到减速度 max_z_velocity:20#Z轴最大速度 max_z_accel: 100#Z轴最大加速度 square_corner_velocity: 15#方形拐角速度 ### # 运动和驱动参数 ### [stepper_x] step_pin: PE3 dir_pin: PE2 enable_pin: !PE4 #使能引脚 ...
toolhead: Replace max_accel_to_decel with minimum_cruise_ratio 0105aa3· Mar 14, 2024 HistoryHistory Breadcrumbs klipper /docs / Status_Reference.mdTop File metadata and controls Preview Code Blame 570 lines (473 loc) · 23.1 KB Raw Status reference This document is a reference of p...
TheM201,M203,M204, andM205commands are implemented by calling Klipper'sSET_VELOCITY_LIMITcommand. For calls that set theACCELparameter, theACCEL_TO_DECELparameter is also set and scaled byvariable_velocity_decel_scale(default:0.5). TheM900command is implemented by calling Klipper'sSET_PRESSURE_ADV...