port-mode trunk; vlan { members [ vlan-100 vlan-110 vlan-120 ]; } } } } vlan { unit 100 { family inet { address 10.1.100.1/24; } } unit 110 { family inet { address 10.1.110.1/24; } } unit 120 { family inet { address 10.1.120.1/24; ...
[匚 IT 0 T- A 0-JI B- 5k 」j 立匸13 ■勺呈踽五￥ (sioatMi: trhiemct Options 配置完成后点击“ ok”,确认配置 2.2接口 Trunk模式配置 SRX防火墙接口支持trunk模式,编辑对应接口,在“ Ethernet Switching Parameters ”下钩 选“Enable Ethernet Switching ”,选择 “Port Mode 为“trunk ”,还可以...
allow you to import routes from one routing table to another. In this scenario, the static route within the routing instance needs access to the inet.0 routes, which is facilitated by configuring a RIB group. Junipers documentation outlines RIB groups as a necessary component for handling instan...
把ge0/0/0 从vlan809设置成vlan917 root@qnqy-dpf-jrex2200-01#et interfaces ge-0/0/0 unit 0 family ethernet-switching port-mode access {master:0}[edit]root@qnqy-dpf-jrex2200-01# delete interfaces ge-0/0/0 unit 0 family ethernet-switching vlan members 809 {master:0}[edit]root@qnqy...
1、Juniper SRX 防火墙配置手册 Juniper SRX防火墙配置说明 1 系统配置 1 1.1 配置ROOT帐号密码 1 1.2 配置用户名和密码 2 2 接口配置 8 2.1 IPV4地址配置 9 2.2 接口 TRUNK模式配置 13 2.3 接口 ACCESS模式配置 14 3 VLAN 配置 15 3.1 创建VLAN 配置 15 4 路由配置 19 4.1 静态路由配置 21 5 自定义...
set interfaces ge-0/0/22 unit 0 family ethernet-switching port-mode access set interfaces ge-0/0/22 unit 0 family ethernet-switching vlan members vlan_54 set interfaces ge-0/0/23 unit 0 family ethernet-switching port-mode trunk set interfaces ge-0/0/23 unit 0 family ethernet-switching ...
set interfaces ge-0/0/22 unit 0 family ethernet-switching port-mode access set interfaces ge-0/0/22 unit 0 family ethernet-switching vlan members vlan_54 set interfaces ge-0/0/23 unit 0 family ethernet-switching port-mode trunk set interfaces ge-0/0/23 unit 0 family ethernet-switching ...
Juniper防火墙基本命令---4ac6a1ae-6ea4-11ec-9abc-7cb59b590d7djuniper防火墙基本命令常用查看命令getint查看接口配置信息Getintethx/X查看指定接口的配置信息getmip查看映射IP关系getroute查看路由表getpolicyidx查看指定策略getnsrp查看nsrp信息,后可接参数查看具体vsd组、端口监控设置等getpercpude查看cpu利用率信息...
指定接口指定管理选项 Setintethx/xphyfull100mb配置指定接口速率及双工方式Setint ethx/xphylink-down配置指定接口shutdown Setnsrpvsdid0monitorinterfaceethx/x配置ha监控端口,如此 端口断开,则设备发生主/备切换 Execnsrpvsd0modebackup手工迚行设备主/备切换,在当前的主 设备上执行 setroute/0interfaceethernet1/3...
I have a lot of problems with the connection between our Cisco 2950 and Juniper EX4200. We got two different types of connection, two swtiches with LAG (LACP) and three switches with standard Trunk (STP). The Problem: If i connect a new switch to