set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside then source-nat interface √ 策略policy 配置示例: set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match source-address CBGZ-out-norestrict set security policies from-zone trust to-...
set security nat destination rule-set dst-nat-rulerule 12 match destination-address 222.0.0.8/32 set security nat destination rule-set dst-nat-rule rule 12 match destination-port 8080 to 8081 set security nat destination rule-set dst-nat-rule rule 12 then destination-natpool test3 set security...
root@SRX1400# set security nat source rule-set 1 from zone trust root@SRX1400# set security nat source rule-set 1 to zone untrust root@SRX1400# set security nat source rule-set 1 rule rule1 match source-address 0.0.0.0/0 destination-address 0.0.0.0/0 root@SRX1400# set security nat so...
root@SRX1400# set security nat destinationpool dst-nat-pool-1 address 172.16.1.1/32 root@SRX1400# set security nat destinationpool dst-nat-pool-1 address port 80 root@SRX1400# set security nat destinationrule-set rs1 from zone untrust root@SRX1400# set security nat destinationrule-set rs1 r...
Juniper SRX防火墙NAT配置简介 基于源IP地址的NAT 基本的实验拓扑：◆实验前的基本配置 ◆NAT配置前我们首先保证从Trust路由器可以直接访问Untrust路由器，防火墙的基本配 置如下：#初始化化防火墙接口，并将接口划入到相应的Zone set interfaces ge-0/0/0 unit 0 family inet address 10.1.1.10/24 set interfaces...
SRX Nat介绍 1、Source NAT //转换源的NAT,NAT+Gloabl 2、Destination NAT //Static pat 3、Static NAT //静态一对一转换 SRX NAT处理流程 : 优先static nat ---destination nat---source nat NAT 查询与处理顺序 --- 第二部分:Source NAT: Interface NAT Interface NAT SRX platforms support NAT configu...
1.1基于Interface的Source NAT 公司内部网络(trust Zone)访问Internet(untrust Zone)时,将192.168.100.0/24 映射成Juniper SRX的GE-0/0/0端口的IP地址202.5.5.1出Internet。 a、配置基于接口的source NAT set security nat source rule-set src-nat from zone trust ...
Juniper(JUNOS) SRX建立NAT端口映射 Juniper(JUNOS)建立NAT端口映射 1、NAT配置界面介绍: Rule Name:对该NAT的命名(不影响配置); Source Address:对源地址的限制(可以不填,若要限制可以在Policy处设置)。 Deatination Address & Port:外网地址,对应的外网地址端口。
SRX的NAT配置分为源地址翻译(source NAT),目标地址翻译(destination NAT)和静态地址翻译(static NAT)三种,其配置语法都类似,只是natrule必须被放到rule-set里使用,任意两个zone或任意两个网络逻辑接口之间只允许有一个rule-set。 值得注意的是SRX不会自动为NAT规则生成proxy-arp配置,因此如果NAT地址翻译之后的地址跟...
上述配置定义Policy策略,允许Trust zone 10.1.2.2地址访问Untrust方向任何地址,根据前面的NAT配置,SRX在建立session时自动执行接口源地址转换。 1.2Pool based Source NAT NAT:set security nat source pool pool-1 address 100.1.1.10to 100.1.1.20 set security nat source rule-set1from zone trust set security nat...