1、指定主备On device A: set chassis cluster cluster-id 1 node 0 reboot On device B: set chassis cluster cluster-id 1 node 1reboot定义控制层端口 (可配置网管口)On device A:primary:node0set groups node0 system host-name HQ-CS-FW-SRX550-1 set groups node1 system host-nameHQ-CS-FW-...
当两台SRX设备形成ChassisCluster后配置会自动从主节点向备用节点进行同步,可以手动使用以下命令关闭同步:set chassis cluster configuration-synchronizeno-secondary-bootup-auto command in configuration mode.或者使用以下命令打开自动同步:delete chassis cluster configuration-synchronizeno-secondary-bootup-auto command in...
set chassis cluster redundancy-group 1 interface-monitor ge-5/0/3 weight 255 set chassis cluster redundancy-group 1 interface-monitor ge-5/0/4 weight 255 13.如果在配置过程中,需要进行出厂值恢复 A.关闭cluster,并且重启设备 SRX-A>set chassis cluster disable reboot SRX-B>set chassis cluster disab...
SRX Series Chassis Cluster Slot Numbering, and Physical Port and Logical Interface Naming 4.定义数据层端口 On device A: {primary:node0} -fab0 is node0 (Device A) interface for the data link # set interfaces fab0 fabric-options member-interfaces ge-0/0/2 ...
SRX通过set语句来配置防火墙,通过delete语句来删除配置,如delete security nat和edit security nat / delete一样,均可删除security防火墙层级下所有NAT相关配置,删除配置和ScreenOS不同,配置过程中需加以留意。 部署SRX防火墙主要有以下几个方面需要进行配置:
Juniper SRX防火墙HA配置(juniper交换机) 一、实验环境介绍1)vsrx 12.1X47-D20.7 vSRXA1与vSRXA2之间建议Chassis Clusterge-0/0/0为带外管理接口(系列默认,不可改)ge-0/0/1为control-link(系统配置,不可改)ge-0/0/4为data-link(手工配置,可改)control-link与data-link采用背靠背的连接方式。
Here is how we got it happily working (assuming you have a chassis cluster up and running): SRX Config: set interfaces ge-2/0/0 gigether-options redundant-parent reth1 set interfaces ge-2/0/1 gigether-options redundant-parent reth1 ...
SRX-B>set chassis cluster cluster-id 1 node 1 reboot 以上两句配置后,设备自动重启,命令不显示。 指定Control Port(如果主控板RE上有固定control-ports,则无需指定,SRX5800需配置,SRX3600无需配置): 在主防火墙上在configure模式下执行,在备防火墙上用configure shared分别执行如下两条命令: set chassis cluster...
Chassis Cluster 十三、Service 开启DHCP Author :Ltm Email :network-security@ QQ root@ltm# run show configuration system services dhcp | display set set system services dhcp name-server 0 set system services dhcp router set system services dhcp pool /24 address-range low set system services dhcp ...
Juniper SRX通用手册 一、理解物理端口&逻辑接口命名 在设备作为集群连接之后,一个设备上的插槽编号会发生变化,因此接口编号也会发生变化。两个节点中每个槽的槽号使用以下公式确定: cluster slot number = (node ID * maximum slots per node) + local slot number...