我用的EFM8UB1,通过debug的1,2,3,4脚(VTARGET接了一个3.3v电压),2,4,3(C2D、C2CK、GND)与另外一块板子的Direct Debug Connector引脚相连,然后接了一个3.3v的电压给外部板的vmuc。设置按照楼主的方式设置,但是烧录一次以后就无法再次连接目标设备,而且外部的芯片非常的烫。 Mia_世强回复: 首先,确认一下...
Pin 2 is not connected inside J-Link. A lot of targets have pin 1 and pin 2 connected. Some targets use pin 2 instead of pin 1 to supply VCC. These targets will not work with J-Link, unless Pin 1 and Pin 2 are connected on the target's JTAG connector. Pin 3 (TRST) should be...
[3] Flash system [4] Exit Enter your Selection:1 NAND erase: device 0 offset 0x0, size 0x200000 Erasing at 0x180000 -- 100% complete. OK Insert a OTG cable into the connector! 设置虚拟机的USB接口 : 之前写过, 详情见 http://blog.csdn.netshulianghan/article/details/42254237#t45 ;...
For programming the image via J-Link connector, the JLink path need to be declared in WICED build string. Add the path of JLink.exe from the downloaded J-Link tool. Example: For downloading test.console application, make the target as follows test.console-CYW9...
在淘宝,您不仅能发现JLINK-RX-AD[ADAPT BD FOR MINI-JTAG CONNECTOR]的丰富产品线和促销详情,还能参考其他购买者的真实评价,这些都将助您做出明智的购买决定。想要探索更多关于JLINK-RX-AD[ADAPT BD FOR MINI-JTAG CONNECTOR]的信息,请来淘宝深入了解吧!
And will this J-Link support debugging through the J8 connector (JTAG or SWD) Thanks Images J-Link status.jpg 81.99 kB, 680×346, viewed 986 times SEGGER - Alex Administrator Posts 2,106 2 Aug 23rd 2012 Hi, Does the KwikStik work with an eval board? If yes, could ...
今天痞子衡给大家分享的是实践JLink 7.62手动增加新MCU型号支持新方法。文接上篇 《从JLink V7.62开始优化了手动增加新MCU型号支持方法》,文章发出之后,有小伙伴留言说不是保姆级教程,没有看懂,看起来光有理论还不行,必须加上实操。好,我们现在来实践一下,选一个 V7.
The JLINK-ARM-AD is designed to work with FDI’s products that utilize a mini-JTAG connector. Products include the following: uEZGUI-xxx-43WQS uEZGUI-xxx-70WVE SOMDIMM-LPCxxxx This product is intended for users who currently own a standard 20-pin JTAG debugger that is compatible with ARM...
9、Standard 2x10 pin JTAG connector 10、Automatic core recognition 11、Auto speed recognition 12、Support for multiple devices on scan chain 13、Fully plug-and-play compatible 14、All JTAG signals can be monitored 15、Supports 1.2-3.3 V target voltage ...
i have some problems with my mk20dx256vlh7 boards. Some of them work perfectly, but i have boards they seem to by protected.i have checked the soldering, vbat, reset and connector everything is fine. i use the segger jlink flash tool. is there any reset script or an oth...