现在先为 Orin 装上鼠标、键盘以及 DP(Display Port)接口显示器就能使用,如果您手边没有直接的 DP 显示器的话,使用部分品牌的 DP to VGA 转接头也可以。 开机之后就进入上图 “Step 1. Ubuntu setup(oem-config)” 阶段,进行以下 9 个步骤的系统配置工作: 1、同意授权:点选左下角 “I accept the terms...
现在先为Orion装上鼠标、键盘以及DP(Display Port)接口显示器就能使用,如果您手边没有直接的DP显示器的话,使用DP to VGA转接头也是可以,目前测试过DP to HDMI转接方式是有问题的。 开机之后就进入上图“Step 1.Ubuntusetup(oem-config)”阶段,进行以下9个步骤的系统配置工作: 1. 同意授权:点选左下角“I acce...
Selecting previously unselected package nvidia-l4t-oem-config. Preparing to unpack .../nvidia-l4t-oem-config_32.6.1-20210726122859_arm64.deb ... Unpacking nvidia-l4t-oem-config (32.6.1-20210726122859) ... Selecting previously unselected package nvidia-l4t-tools. Preparing to unpack .../nvidia-l4...
STEP 02 只勾选Jetson Linux,选择I accept the terms and conditions of the license agreements,点击Create,然后CONTINUE,输入虚拟机密码,等待下载完成,如果中间出现问题,就是有些没有下载下载,更换网络后,重新登录下载(重新登录是必要的) 安装过程,出现以下界面,OEM Configuration下拉选择runtime 等待安装完成,中间可能...
Step03:选择Manual Setup,OEM Configuration选择Runtime,点击Flash,后面只需要等待系统烧录完成,烧录过程比较漫长。 Step04:待系统烧录完成后,立即拔掉Jetson NX的电源线、拔掉USB线、拔掉第二引脚和第三引脚上的杜邦线。给Jetson NX重新接上电源线,接上显示器连接线,接上网线,接上键鼠无线接收器,在Jetson开机过程中...
Reconfiguring a Jetson Device with oem-config To re-enable oem-config manually on a flash drive To re-enable oem-config manually on an SD card About Communication Through the Debugging Port To configure oem-config to use a 40-pin header UART port Headless Mode Flow in oem-config To reconf...
For the OEM Configuration, you have two options: Runtime: If you choose this option, the username/password creation will be prompted when you boot the Orin after the flash. Pre-Config: With this option, you will create the username/password for the Orin before flashing. ...
(3)对于oem-config,连接jetson micro usb端口到ubuntu主机 使用波特率为115200的minicom 在jetson nano的第一次启动时打开主机上的/dev/ttyACM0节点 4. 目前使用nano机型 5.在oem-config上工作 可以在设备启动后检查dtb。 没有显示原始设备配置。 但是Jetson Micro-USB接口可以工作 ...
When a freshly initialized SD card is first booted it runsoem-config, one of whose functions is to set the APP partition’s size. It does the following things: Moves the backup GPT header to the end of the disk Deletes and re-creates the root partition ...
Ignore 7, OEM configuration. Select your desired storage device to flash the L4T BSP to for 8, Storage Device. ClickFlashbutton. When flashing is done, the Jetson developer kit will reboot and boot into the L4T BSP. Yon can complete the OEM Config as describedhere. ...